- 您现在的位置：买卖IC网 > Datasheet目录590 > 1-1490413-6 (TE Connectivity)TOOL NEST DIE HD SEAMLESS 4AWG Datasheet资料下载
参数资料
| 型号： | 1-1490413-6 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/5页 |
| 文件大小： | 0K |
| 描述： | TOOL NEST DIE HD SEAMLESS 4AWG |
| 标准包装： | 1 |
| 压接或电缆尺寸： | 4 AWG |
| 压接手柄： | 1490748-1，1490749-1 |
| 连接器类型： | 端子及连接件 |
408- 10110
!
3. Insert the stripped wire into the wire barrel of the
terminal or splice making sure that the end of the
wire is visible through the sight hole.
4. Center the terminal or splice in the nest as
shown in Figure 4.
DANGER To avoid personal injury, make sure to exercise
caution when holding terminals, splices, or wire
near the crimping area.
Terminal or Splice
Centered in Nest
(See Detail)
8. For splices, insert a stripped wire into the
uncrimped wire barrel until the end of the
conductor is visible in the sight hole.
9. Inspect the crimp according to Figure 5. This is
included as an aid to the tool operator ONLY. It is
not intended to serve as a quality control
inspection for qualifying finished crimps on these
terminals and splices. Use only terminals or splices
that meet the conditions shown in the ACCEPT
column. Terminals and splices displaying the
features shown in the REJECT column can be
avoided by careful use of these instructions and by
performing the maintenance and inspection
procedures described in Section 5.
CAUTION Damaged terminals or splices should not be
used. If a damage is evident, the terminal or
splice should be cut from the wire and replaced
with a new one. DO NOT re--terminate terminals
or splices.
5. MAINTENANCE AND INSPECTION
DANGER
To avoid personal injury, DISCONNECT THE
POWER SUPPLY before performing
maintenance, adjustments, inspection, or repair.
Nest
Terminal
Detail
Sight Hole
Facing Nest
Nest
Splice
Sight Hole
Facing Nest
5.1. Daily Maintenance
It is recommended that each operator of the dies be
made aware of, and responsible for, the following
steps of daily maintenance:
1. Remove dust, moisture, and other contaminants
from the dies with a clean brush, or a clean, soft,
lint--free cloth. DO NOT use objects that could
damage the dies.
Wire Visible
Through
Indenter
Indenter
Sight Hole
Wire Visible
Through
Sight Hole
Figure 4
5. Activate the head or tool according to the
instructions included with the head or tool so that
ram advances and holds the terminal or splice in
place. DO NOT deform the wire barrel.
6. For terminals, insert the stripped wire into the
wire barrel until the end of the conductor is visible
in the sight hole. For butt splices, insert a stripped
wire into the wire barrel until the end of the
conductor is visible in the sight hole.
7. Activate the head or tool to crimp the wire
barrel.
2. If dies are coated with oil or preservative, wipe
them clean—particularly in the crimping
areas—before placing them in use.
3. When dies are not in use, make certain all
surfaces are protected with a THIN coat of any
good SAE 20 motor oil, then mate and store them
in a clean, dry area.
5.2. Periodic Inspection
Periodic inspections should be performed by quality
control personnel. A record of scheduled inspections
should remain with the dies or be made available to
personnel responsible for the dies. Though
recommendations call for at least a monthly
inspection, the inspection frequency should be based
upon the amount of use, working conditions, operator
training and skill, and established company
standards. These inspections should be performed in
the following sequence.
NOTE
i
Rev D
If the terminal or splice sticks in the die after
crimping, grasp the wire close to the crimp and
apply a rocking motion to remove it from the die.
A. Visual Inspection
1. Remove all lubrication and accumulated film by
immersing the dies in a suitable degreaser that will
not affect paint or plastic.
3 of 5
相关PDF资料 |
PDF描述 |
|---|---|
| 1-1579002-2 | TOOL HAND STRIPPER |
| 1-1579002-7 | TOOL HAND STRIPPER AND CUTTER |
| 1-1579004-1 | TOOL HAND CRIMPING SOLARLOK |
| 1-1579007-2 | EXTRACTION TOOL |
| 1-1579007-3 | EXTRACTION TOOL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 1-1490413-7 | 功能描述:手工工具 NEST HD SEAMLESS 2 & 1 RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 1-1490413-8 | 功能描述:手工工具 NEST HD SEAMLESS 1/0 RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 1-1490413-9 | 功能描述:手工工具 NEST HD SEAMLESS 2/0 RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 114-90-422-41-117 | 制造商:PREDIP 制造商全称:Precid-Dip Durtal SA 功能描述:Dual-in-line sockets and headers Open frame / surface mount |
| 114-90-424-41-117 | 制造商:PREDIP 制造商全称:Precid-Dip Durtal SA 功能描述:Dual-in-line sockets and headers Open frame / surface mount |
发布紧急采购，3分钟左右您将得到回复。