- 您现在的位置：买卖IC网 > Datasheet目录542 > 1-49935-0 (TE Connectivity)TOOL HEAD CRIMP 22-10AWG SOLIS Datasheet资料下载
参数资料
| 型号： | 1-49935-0 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/5页 |
| 文件大小： | 0K |
| 描述： | TOOL HEAD CRIMP 22-10AWG SOLIS |
| 标准包装： | 1 |
| 系列： | Solistrand, Strato-Therm |
| 压接或电缆尺寸： | 10-22 AWG |
| 压接手柄： | 1213563-1，1213804 |
| 连接器类型： | 端子及连接件 |
| 配用： | 8-330368-1-ND - CONN BUTT SPLICE UNINS 14-16AWG 328600-ND - CONN BUTT SPLICE UNINS 10-12AWG 328427-ND - CONN BUTT SPLICE 14-16AWG NATRL 326819-ND - CONN RING 16-22AWG #6 BLACK 326742-ND - CONN BUTT SPLICE 10-12AWG YELLOW 2-323683-1-ND - CONN RING 10-12AWG #1/4 ORANGE 322824-ND - CONN BUTT SPLICE UNINS 14-16AWG 2-321896-2-ND - CONN RING 16-22AWG #10 ORANGE 320263-ND - CONN HOOK 14-16AWG #8 BLUE 8-34147-1-ND - CONN RING 16-22AWG #6 RED 更多... |
| 相关产品： | 1213563-1-ND - TOOL DAHT ADAPTER ASSEMBLY |
408-10034
5. Your own established standards.
Terminal
Wire Barrel Centered
in Crimping Chamber
Flat Side of Terminal
Tongue Facing Anvil
Butt Splice
Wire Barrel Centered
in Crimping Chamber
Brazed Seam on
Splice Toward
Indenter
Parallel Splice
Wire Barrel Centered
in Crimping Chamber
Figure 3
5. CRIMP INSPECTION
Inspect crimped terminals and splices by checking the
features described in Figure 4. Use only terminals or
splices that meet the conditions shown in the
“ACCEPT” column. “REJECT” terminations can be
avoided through careful use of instructions in Section
4, and by performing regular head maintenance, as
described in Section 6.
6. MAINTENANCE AND INSPECTION
DANGER To avoid personal injury, ALWAYS disconnect the
battery from the tool before performing
STOP maintenance or inspection.
Tyco Electronics recommends that a maintenance and
inspection program be performed periodically to
ensure dependable and uniform terminations. The
crimping head should be inspected once a month.
Frequency of inspection should be adjusted to suit
your requirements through experience. Frequency of
inspection depends on:
1. The care, amount of use, and handling of the
crimping head.
2. The type and size of the product crimped.
3. The degree of operator skill.
4. The presence of abnormal amounts of dust
and dirt.
Rev B
Each crimping head is thoroughly inspected before
packaging. Since there is the possibility of crimping
head damage during shipment, new crimping heads
should be inspected immediately upon arrival at your
facility.
6.1. Daily Maintenance
Tyco Electronics recommends that each operator be
responsible for the following steps of daily
maintenance:
1. Remove dust, moisture, and other
contaminants with a clean, soft brush, or a lint-
free cloth. Do NOT use objects that could
damage the head.
2. Make sure that all pins, rings, and other
components are in place and secure.
DANGER To avoid personal injury and damage to the tool,
make sure quick pins are properly inserted.
STOP
3. Make certain all surfaces are protected with a
thin coat of any good SAE 20 motor oil. Do NOT
oil excessively.
4. When the head assembly is not in use, store it
in a clean dry, area.
6.2. Periodic Inspection
Regular inspections should be performed by quality
control personnel. A record of scheduled inspections
should remain with the crimping heads or be supplied
to supervisory personnel responsible for the crimping
heads. Though recommendations call for at least one
inspection a month, the frequency should be based on
amount of use, working conditions, operator training
and skill, and your established company policies.
These inspections should include a visual inspection
(Paragraph 6.3) and a crimping chamber inspection
(Paragraph 6.5).
6.3. Visual Inspection
1. Remove all lubrication and accumulated film by
immersing the crimping head in a suitable
commercial degreaser that will not affect paint or
plastic.
2. Make certain all components are in place.
3. Check all bearing surfaces for wear.
4. Inspect crimp area for flattened, chipped, or
broken areas. Replace worn or damaged parts.
3 of 5
相关PDF资料 |
PDF描述 |
|---|---|
| 0010844061 | 084 DIA ASSY HDR HSG PIN 94V-0 |
| 0011020001 | INSERTION TOOL HT1807 |
| 0011020003 | INSERTION TOOL HT1353 |
| 0011030003 | EJECTOR EXTRACTION TOOL HT1884 |
| 0011030016 | TOOL EXTRACTION MOLEX .156 TERM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 1499363 | 制造商:UNBRANDED 功能描述:INDICES MULTICOLOUR BLANK 10PART |
| 1-499374-0 | 功能描述:集管和线壳 050 UNIV HDR SP 4S 30DP STD L2 RoHS:否 产品种类:1.0MM Rectangular Connectors 产品类型:Headers - Pin Strip 系列:DF50 触点类型:Pin (Male) 节距:1 mm 位置/触点数量:16 排数:1 安装风格:SMD/SMT 安装角:Right 端接类型:Solder 外壳材料:Liquid Crystal Polymer (LCP) 触点材料:Brass 触点电镀:Gold 制造商:Hirose Connector |
| 14993741 | 制造商: 功能描述: 制造商:TE Connectivity 功能描述: 制造商:undefined 功能描述: |
| 1-499374-1 | 制造商:TE CONNECTIVITY 功能描述:060 UNIV HDR SP 4S 30DP STD L2 |
| 1-499376-0 | 制造商:TE CONNECTIVITY 功能描述: |
发布紧急采购，3分钟左右您将得到回复。