参数资料
| 型号： | 1-5-467MP |
| 厂商： | 3M (TC) |
| 文件页数： | 7/9页 |
| 文件大小： | 0K |
| 描述： | TAPE TRANSFER ADHESIVE 1" X 5YD |
| MSDS 材料安全数据表： | 467MP,468MP,9667MP,9668MP(L) MSDS |
| 标准包装： | 1 |
| 系列： | 467MP |
| 胶带类型： | 胶粘传输带 |
| 胶合剂： | 丙烯酸，200MP |
| 背衬，载体： | 聚乙烯涂层牛皮纸内衬 |
| 厚度： | 0.0065"（6.5 mils，0.165mm） |
| 厚度 - 胶合剂： | 0.0023"（2.3 mils，0.058mm） |
| 厚度 - 背胶，载体，衬垫： | 0.0042"（4.2 mils，0.107mm） |
| 宽： | 1.00"（25.40mm） |
| 长度： | 15'（4.6m）5 码 |
| 颜色： | 透明 |
| 使用： | 连接件，高温应用 |
| 包装： | 散装 |
| 其它名称： | 3M9727 |
3M? Adhesive Transfer Tapes with Adhesive 200MP
467MP, 468MP, 467MPF, 468MPF, 7952MP, 7955MP, 7962MP, 7965MP, 9172MP,
9185MP, 9667MP, 9668MP
Master Width
Product
467MP
468MP
467MPF
468MPF
7952MP
7955MP
7962MP
7965MP
9172MP
9185MP
9667MP
9668MP
Master Width
48” or 60” (1.22 or 1.52 m)
54” (1.37 m)
48” (1.22 m)
54” (1.37 m)
More sizes may be available. Please call 800-223-7427 or talk to your local
3M representative for more information.
Application Techniques
For maximum bond strength (during installation of the final part) the surface
should be thoroughly cleaned and dried. Typical cleaning solvents are
heptane (for oily surfaces) or isopropyl alcohol for plastics. Use reagent grade
solvents since common household materials like rubbing alcohol frequently
contain oils to minimize the drying affect on skin and can interfere with the
performance of a pressure-sensitive adhesive.
*Note: Carefully read and follow the manufacturer’s precautions and
directions for use when working with solvents. These cleaning
recommendations may not be in compliance with the rules of certain air
quality management districts in California; consult applicable rules before
use.
It is necessary to provide pressure during lamination (1.5-20 pli
recommended) and during final part installation (10-15 psi) to allow the
adhesive to come into direct contact with the substrate. Using a hard edged
plastic tool, which is the full width of the laminated part, helps to provide the
necessary pressure at the point of lamination. Heat can increase bond strength
when bonding to metal parts (generally this same increase is observed at
room temperature over longer times, weeks). For plastic parts, the bond
strength is not enhanced with the addition of heat.
The ideal adhesive application temperature range is 60°F (15.6°C) to 100°F
(38°C). Application is not recommended if the surface temperature is below
50°F (10°C) because the adhesive becomes too firm to adhere readily. Once
properly applied, at the recommended application temperature, low
temperature holding is generally satisfactory (please refer to section VII of
the Typical Physical Properties and Performance Characteristics).
When bonding a thin, smooth, flexible material to a smooth surface, it is
generally acceptable to use 2 mils of 3M? Adhesive 200MP. If a texture is
visible on one or both surfaces, the 5 mil 3M adhesive 200MP would be
suggested. If both materials are rigid, it may be necessary to use a thicker
adhesive to successfully bond the components. 3M? VHB? Acrylic Foam
7
相关PDF资料 |
PDF描述 |
|---|---|
| GSP2.8113.11 | GSP2 APPLIANCE INLET 10A 70 |
| 6200.4125 | MOD PWR ENTRY 1PL QC 2.5MM SNAP |
| 6200.4210 | MOD PWR ENTRY 1PL QC 1MM SNAP-IN |
| 6200.4130 | MOD PWR ENTRY 1PL QC 3MM SNAP-IN |
| 6200.4230 | MOD PWR ENTRY 1PL QC 3MM SNAP-IN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 1-5-467MP (CASE OF 10) | 功能描述:3M 467MP ADHESIVE TRANSFER TAPES 制造商:3m (tc) 系列:467MP 零件状态:在售 温度范围:-40°F ~ 300°F（-40°C ~ 149°C） 标准包装:10 |
| 1546806-1 | 制造商:TE Connectivity 功能描述:1/2 TO 3/8 REDUCER CONN,FLEXA - Bulk |
| 1546806-3 | 制造商:TE Connectivity 功能描述:1 TO 3/8 REDUCER CONN,FLEXA - Bulk |
| 1546806-4 | 制造商:TE Connectivity 功能描述:1 TO 1/2 REDUCER CONN,FLEXA - Bulk |
| 1546806-5 | 制造商:TE Connectivity 功能描述:3/4 TO 1/2 REDUCER CONN,FLEXA - Bulk |
发布紧急采购，3分钟左右您将得到回复。