- 您现在的位置：买卖IC网 > PDF目录18495 > 1-543013-1 (TE Connectivity)TOOL DIE SET CRIMP .525 CABLE PDF资料下载
参数资料
| 型号： | 1-543013-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/4页 |
| 文件大小： | 0K |
| 描述： | TOOL DIE SET CRIMP .525 CABLE |
| 标准包装： | 1 |
| 系列： | AMPLIMITE |
| 压接手柄： | 543344-1 |
| 连接器类型： | Amplimite HD 连接器 |
| 相关产品： | A23576-ND - TOOL HAND CRIMP FOR FERRULE DIE |
408-9318
Back Side of Tool
Crimping
Chamber
Outer Ferrule Lip
Positioned Against Stop
Cable
Inner Ferrule Lip
Positioned in Slot of
Positioner
Anvil
Die
Tool Flip-Top
Latch
Figure 3
4.2. Inspection
Regular inspections should be performed with a
record of inspections remaining with the dies and/or
supervisory personnel responsible for them. Tyco
Electronics recommends one inspection per month;
however, amount of use, working conditions, operator
training and skill, and established company standards
should determine frequency of inspection. The
inspection should be performed in the following
sequence:
A. Visual Inspection
1. Remove all lubrication and accumulated film by
immersing the dies in a suitable commercial
degreaser that will not affect paint or plastic
material.
2. Make sure all die mounting screws are in place
and secured.
3. Check all bearing surfaces for wear. Replace
4. Inspect the crimping chamber for flattened,
chipped, cracked, worn, or broken areas. If
damage is evident, the dies must be replaced.
Rev E
B. Die Opening Inspection
This inspection requires the use of a vernier caliper.
Proceed as follows:
1. Mate the dies until the crimping surfaces have
bottomed; then hold in this position.
2. Using a vernier caliper, measure the die
the dies are considered dimensionally correct and
should be lubricated with a thin coat of any good SAE
20 motor oil. If not, the dies must be replaced. Refer to
5. REPLACEMENT
Order replacement dies through your Representative,
or call 1-800-526-5142, or send a facsimile of your
purchase order to 717-986-7605, or write to:
CUSTOMER SERVICE (38-35)
TYCO ELECTRONICS CORPORATION
PO BOX 3608
HARRISBURG PA 17105-3608
6. REVISION SUMMARY
Revisions to this instruction sheet include:
? Updated instruction sheet to corporate
requirements
3 of 4
相关PDF资料 |
PDF描述 |
|---|---|
| 1-543013-0 | TOOL DIE SET CRIMP .530 CABLE |
| 51CAD-E24-B13L | POT 5K OHM 1/2" SQ 1/2W PLAS |
| 51SAD-U25-A20L | POT 100K OHM 1/2" SQ 1W CERMET |
| 51CAD-E24-A20L | POT 100K OHM 1/2" SQ 1W CERMET |
| 1-543013-7 | TOOL DIE SET CRIMP .280 CABLE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 1-543013-2 | 功能描述:折皱器 CRIMP ANVIL SUBASSY RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| 1-543013-3 | 功能描述:折皱器 CRIMP ANVIL SUBASSY RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| 1-543013-4 | 功能描述:折皱器 CRIMP ANVIL SUBASSY RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| 1-543013-5 | 功能描述:折皱器 CRIMPER ANVIL SUBASSY RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| 1-543013-6 | 功能描述:冲压机与冲模 CRIMPER ANVIL RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
发布紧急采购，3分钟左右您将得到回复。