- 您现在的位置：买卖IC网 > Datasheet目录590 > 1-543013-6 (TE Connectivity)TOOL DIE SET CRIMP .280 CABLE Datasheet资料下载
参数资料
| 型号： | 1-543013-6 |
| 厂商： | TE Connectivity |
| 文件页数： | 1/4页 |
| 文件大小： | 0K |
| 描述： | TOOL DIE SET CRIMP .280 CABLE |
| 标准包装： | 1 |
| 系列： | AMPLIMITE |
| 压接手柄： | 543344-1 |
| 连接器类型： | Amplimite HD 连接器 |
| 相关产品： | A23576-ND - TOOL HAND CRIMP FOR FERRULE DIE |
Crimping Die Assemblies
543013-[ ]
Instruction Sheet
408-9318
23 NOV 10 Rev E
PROPER USE GUIDELINES
Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low
volume applications. A wide selection of powered application equipment for extended-use, production operations is available.
Crimper
(Stationary Die)
Die Holding
Screw
2. DESCRIPTION
Each die assembly consists of an anvil (moving die)
and a crimper (stationary die). The anvil features an
inner ferrule positioner and an outer ferrule stop. Each
die is held in the tool frame by a single screw. Refer to
Outer Ferrule
Stop
Inner Ferrule
Positioner
Anvil
(Moving Die)
Identification
Marking
When mated, the dies form a crimping chamber which
simultaneously crimps the inner and outer ferrule onto
the cable. The dies and the positioner have an
identification marking to ensure proper die selection
for the ferrules being crimped.
3. CRIMPING PROCEDURE
The ferrules must be crimped before the
NOTE
contacts are crimped.
i
Determine the outside diameter of the cable being
used, then refer to Figure 2 to select the appropriate
inner and outer ferrule and then the corresponding die
assembly. Observe the identification marking on the
i
Figure 1
1. INTRODUCTION
Crimping Die Assemblies 543013-[ ] are designed to
be used in Hand Crimping Tool Frame Assembly
543344-1 to crimp the inner ferrule and outer ferrule
used with shielded cable clamp kits for
AMPLIMITE* HD connectors.
This instruction sheet describes crimping procedures,
insulation crimp adjustments, and maintenance and
inspection. For information concerning the tool frame
and die installation, refer to Instruction Sheet
408-9315 packaged with the tool frame. Read these
instructions and referenced materials before using the
die assembly.
NOTE Measurements are in millimeters [with inches
in brackets]. Figures and illustrations are for
reference only and are not drawn to scale.
Reasons for reissue of this instruction sheet are
Prepare the cable according to the instructions
packaged with the ferrules. Proceed as follows:
NOTE Outer ferrule must be placed on the cable
before stripping the cable.
i
1. Install the die assembly according to the
instructions packaged with the tool frame. Hold the
tool so that the FRONT side is facing you.
2. Open the dies by squeezing the tool handles
together until the ratchet control releases.
3. Open the tool flip-top latch and insert the cable
into the crimping chamber from the BACK side of
the tool.
4. Make sure that the lip of the inner ferrule is in
the slot in the positioner and the lip of the outer
5. After the ferrules are properly positioned, close
the tool flip-top latch.
6. Hold the cable assembly in place and squeeze
the tool handles together until the ratchet
releases.
7. Open the tool handles FULLY, open the flip-top
latch, and remove the crimped assembly from the
dies.
?2010 Tyco Electronics Corporation, Berwyn, PA TOOLING ASSISTANCE CENTER 1-800-722-1111
All Rights Reserved PRODUCT INFORMATION 1-800-522-6752
TE logo and Tyco Electronics are trademarks.
*Trademark. Other products, logos, and company names might be trademarks of their respective owners.
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.tycoelectronics.com
1 of 4
LOC B
相关PDF资料 |
PDF描述 |
|---|---|
| 1-576781-0 | TOOL HEAD CRIMP 16AWG STRATO |
| 1-58142-4 | TOOL INSERT PACE SEAT .125X.250 |
| 1-58150-6 | TOOL INSERT PACE SEAT .100X.200 |
| 1-58166-2 | TOOL SDL FERRULE DIE 8POS |
| 1-601827-2 | TOOL REPL BLADES FOR 601827-2 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 1-543013-7 | 功能描述:折皱器 CRIMP ANVIL SUBASSY RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| 1543016 | 功能描述:环形公制连接器 SACC-MS-5CON-PG1 1-DUO-M SCO RoHS:否 制造商:3M Electronic Solutions Division 产品类型:Connectors 系列:M12 外壳类型:Plug 触点数量:4 安装风格:Cable 端接类型:Solder Cup 电流额定值:4 A |
| 15430212 | 制造商:Delphi Corporation 功能描述:56 Way Base, 24 usable Gray Micro 64 Sealed Female Connector Assembly, Max Current 7 amps |
| 15430213 | 制造商:Delphi Corporation 功能描述:56 Way Base, 26 usable Gray Micro 64 Sealed Female Connector Assembly, Max Current 7 amps |
| 15430215 | 制造商:Delphi Corporation 功能描述:56 Way Base, 10 usable Gray Micro 64 Sealed Female Connector Assembly, Max Current 7 amps |
发布紧急采购，3分钟左右您将得到回复。