- 您现在的位置：买卖IC网 > PDF目录18489 > 1-58166-1 (TE Connectivity)TOOL SDL FERRULE DIE 6POS PDF资料下载
参数资料
| 型号： | 1-58166-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/5页 |
| 文件大小： | 0K |
| 描述： | TOOL SDL FERRULE DIE 6POS |
| 标准包装： | 1 |
| 压接或电缆尺寸： | 0.278" ~ 0.2783"（7.061mm~7.068mm） |
| 压接手柄： | 69710-1 |
| 连接器类型： | 环箍 |
| 相关产品： | A28006-ND - TOOL HAND FRAME W/O DIE ASSY |
Crimping Die Assemblies 58166- [ ] for SDL Connectors
Cable
Connector Body
Clear of Dies
Figure 2
408- 9039
Stationary Die
Front Part of Ferrule
in Braid Crimping
Section of Die
cloth. Do NOT use hard or abrasive objects that
could damage the dies.
2. Make sure dies are protected with a THIN coat
of any good SAE No. 20 motor oil. Do NOT oil
excessively.
3. When die assembly is not in use, mate and
store them in a clean, dry area.
5.2. Periodic Inspection
A. Visual Inspection
1. Remove all lubrication and accumulated film
from the dies by immersing the dies in a suitable
commercial degreaser that will not affect paint or
plastic material.
2. Make sure that all die retention screws and die
components are properly secured.
3. Inspect die assembly for worn, cracked, or
broken surfaces. If damage is evident, the dies
must be replaced. See Section 6, REPLACEMENT
PARTS.
B. Gaging the Crimping Section
This inspection requires the use of plug gages
conforming to the dimensions provided in Figure 4.
Tyco Electronics does not manufacture or market
these gages. For each crimping section, proceed as
follows:
1. Remove traces of oil or dirt from the crimping
section and plug gage.
2. Mate the dies until the crimping surfaces have
bottomed; then hold in this position. DO NOT force
the dies beyond initial contact.
3. Carefully insert GO element into the
corresponding crimping section; do not force it.
The GO element must pass completely through the
crimping section.
4. In the same manner, try to insert the NO--GO
element into the same crimping section. The
NO--GO element may start entry, but must not
pass completely through the crimping section.
Shielded SDL
Connector
Figure 3
Crimped Ferrule
If the crimping sections conform to the gage
inspection, they are considered dimensionally correct,
and should be lubricated with a THIN coat of any
good SAE No. 20 motor oil. If not, the die assembly
must be replaced. Refer to Section 6,
REPLACEMENT PARTS.
For additional information concerning the use of a
plug gage, refer to Instruction Sheet 408--7424.
2 of 5
Tyco Electronics Corporation
Rev F
相关PDF资料 |
PDF描述 |
|---|---|
| 81A1A-B28-B13L | POT 5K OHM 5/8" SQ 1/2W PLAS |
| B32529C1274K289 | FILM CAP 0.2700UF 10% 100V |
| 53RAD-R25-D15L | POT 10K OHM 1/2" SQ 1/4W PLAS |
| 81A1A-B28-A20L | POT 100K OHM 5/8" SQ 2W CERMET |
| 51RAA-R25-A10L | POT 1K OHM 1/2" SQ 1W CERMET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 1-58166-2 | 功能描述:冲压机与冲模 SDL FERRULE DIE 8P RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 1-58166-3 | 功能描述:冲压机与冲模 SDL FERRULE DIE 16 POS RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 1581-7 | 功能描述:测试插头和测试插座 PANEL MOUNT BANANA JACK VIOLET RoHS:否 制造商:Johnson / Emerson Connectivity Solutions 设备类型:Binding Posts 类型:Threaded stud 颜色:Black 电流额定值:15 A 触点电镀:Silver |
| 1581710000 | 制造商:Weidmuller 功能描述:'SO' SL 5.00/180/18 PBT OG - Bulk |
| 1-58172-0 | 功能描述:手工工具 HDI SEATING TL, 3 ROW 40 POSN RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
发布紧急采购，3分钟左右您将得到回复。