- 您现在的位置：买卖IC网 > PDF目录18549 > 1-601967-5 (TE Connectivity)TOOL TURRET TYPE II FOR SOCKET PDF资料下载
参数资料
| 型号： | 1-601967-5 |
| 厂商： | TE Connectivity |
| 文件页数： | 15/17页 |
| 文件大小： | 0K |
| 描述： | TOOL TURRET TYPE II FOR SOCKET |
| 标准包装： | 1 |
| 压接手柄： | 58305-1，601967-1 |
| 连接器类型： | 环箍 |
| 配用： | 601967-1-ND - CRIMPING TOOL M22520/1-01 |
408- 7516
!
i
i
3. Place the back of the turret head over the
retainer ring on the back of the tool. Make sure that
the turret head is seated, then tighten the two
socket head cap screws of the turret head.
4. Rotate the turret until the positioner marked with
the desired contact size is aligned with the index
mark.
5. Press the turret until it is in the locked position.
6. Determine the selector setting according to the
contact size and wire size listed in Figure 3. Pull
the selector knob and turn to the proper setting.
CAUTION The tool handles must be fully opened when
changing the positioner selector setting;
otherwise, damage to the tool will occur.
4. CRIMPING PROCEDURE
NOTE These tools have a ratchet which ensures proper
crimping of the contacts. Once engaged, the
ratchet will NOT release until the tool handles are
FULLY closed.
1. Strip the wire according to the wire size listed in
Figure 3.
2. Squeeze the tool handles together, then allow
the handles to FULLY open.
3. Insert the mating end of the contact into the
indenter from the FRONT of the tool until the
contact bottoms. Refer to Figure 6.
Indenter
Mating End
of Contact
Nameplate
(Ref)
Front of Tool
Figure 6
4. Insert the wire into the contact wire barrel. While
holding the wire in place, squeeze the tool handles
until the ratchet releases. Allow the handles to
open.
5. Remove the crimped contact from the tool.
Inspect the contact according to the applicable
application specification (114--series).
Rev E
5. MAINTENANCE AND INSPECTION
5.1. Daily Maintenance
Each operator should be aware of, and responsible
for, the following steps of daily maintenance, to
ensure continuous quality and reliability of each tool.
1. Remove dust, moisture, and other contaminants
with a clean brush, or soft, lint--free cloth. DO NOT
use objects that could damage the tool.
2. When the tool is not in use, keep the handles
closed, and store the tool in a clean, dry area.
5.2. Gaging the Die Opening (Indenters)
This inspection requires the use of a plug gage
conforming to the dimensions provided in Figure 7.
For plug gages used for periodic general inspection,
see Figure 8. To gage the die opening, proceed as
follows:
1. Remove traces of oil or dirt from the die opening
and plug gage.
2. Fully close tool handles; then hold in this
position. DO NOT force beyond initial contact.
3. Insert GO element into the die opening; but do
not force it. The GO element must pass through
the length of the die opening. See Figure 9.
4. In the same manner, try to insert the NO--GO
element into the die opening. The NO--GO element
may enter partially, but must not pass completely
through the length of the die opening. See
Figure 9.
CAUTION Be careful NOT to crimp the gage element.
!
If the die opening conforms to the gage inspection,
the tool may be considered dimensionally correct and
should be lubricated with a THIN coat of any good
SAE 20 motor oil. If the die opening does NOT
conform to the gage inspection, the tool must be
returned for further evaluation and repair.
For additional information regarding the use of a plug
gage, refer to 408--7424.
5.3. Crimp Height Inspection
NOTE Allowances for tool stresses and relaxation of
contact material were calculated into the crimp
height measurements for military specified
contacts only.
This inspection requires the use of a micrometer, or
equivalent, as shown in Figure 10. It is recommended
using the micrometer (Dial Micrometer 27--9) which
may be purchased from:
B.C. Ames Company
Lexington Street
Waltham, MA 02154
15 of 17
相关PDF资料 |
PDF描述 |
|---|---|
| B32559C8103K289 | CAP FILM 10000PF 630VDC RADIAL |
| WMF6P47K-F | CAP FILM 0.47UF 630VDC AXIAL |
| B82731M2132A30 | D CORE DBL CHOKE 6.8MH 1.3A VER |
| ABLS-13.000MHZ-L4Q-T | CRYSTAL 13.00000 MHZ 18PF SMD |
| FXO-HC736R-49.0908 | OSC 49.0908 MHZ 3.3V HCMOS SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 1-601967-6 | 功能描述:标准环形连接器 POSITIONER TYPE III C RoHS:否 制造商:Hirose Connector 系列:EM-W 产品类型:Accessories 位置/触点数量:1 触点类型: 触点电镀: 安装风格:Cable 外壳材质: 端接类型:Clamp 电压额定值: |
| 160197-000 | 制造商:TE Connectivity 功能描述:160197-000 |
| 1601970000 | 制造商:Weidmuller 功能描述:CONN SHRD HDR M 40 POS 5.08MM SLDR RA TH - Bulk 制造商:Weidmuller 功能描述:SLD 5.08/40/90G 3.2SN OR |
| 1601975-1 | 功能描述:端子 8R25TB MTM .194 X .025 TPBR RoHS:否 制造商:AVX 产品:Junction Box - Wire to Wire 系列:9826 线规:26-18 接线柱/接头大小: 绝缘: 颜色:Red 型式:Female 触点电镀:Tin over Nickel 触点材料:Beryllium Copper, Phosphor Bronze 端接类型:Crimp |
| 1601979 | 制造商:Phoenix Contact 功能描述:RC-17S1N12K0A5 |
发布紧急采购，3分钟左右您将得到回复。