参数资料
型号: 101-0492
厂商: Rabbit Semiconductor
文件页数: 74/110页
文件大小: 0K
描述: INTERFACE OP6800 W/ETHERNET PORT
标准包装: 25
系列: SBC
模块/板类型: 单板计算机模块
适用于相关产品: SR9160
产品目录页面: 618 (CN2011-ZH PDF)
其它名称: 316-1060
62
MiniCom (OP6800)
B.3 Chip Select Circuit
Figure B-1 shows a schematic of the chip select circuit located on the OP6800 module.
Figure B-1. Chip Select Circuit
The current drain on the battery in a battery-backed circuit must be kept at a minimum.
When the OP6800 is not powered, the battery keeps the SRAM memory contents and the
real-time clock (RTC) going. The SRAM has a powerdown mode that greatly reduces
power consumption. This powerdown mode is activated by raising the chip select (CS)
signal line. Normally the SRAM requires Vcc to operate. However, only 2 V is required
for data retention in powerdown mode. Thus, when power is removed from the circuit, the
battery voltage needs to be provided to both the SRAM power pin and to the CS signal
line. The CS control circuit accomplishes this task for the SRAM’s chip select signal line.
In a powered-up condition, the CS control circuit must allow the processor’s chip select
signal /CS1 to control the SRAM’s CS signal /CSRAM. So, with power applied, /CSRAM
must be the same signal as /CS1, and with power removed, /CSRAM must be held high
(but only needs to be battery voltage high). Q3 and Q4 are MOSFET transistors with com-
plementary polarity. They are both turned on when power is applied to the circuit. They
allow the CS signal to pass from the processor to the SRAM so that the processor can peri-
odically access the SRAM. When power is removed from the circuit, the transistors will
turn off and isolate /CSRAM from the processor. The isolated /CSRAM line has a 100 k
pullup resistor to VRAM (R28). This pullup resistor keeps /CSRAM at the VRAM voltage
level (which under no power condition is the backup battery’s regulated voltage at a little
more than 2 V).
Transistors Q3 and Q4 are of opposite polarity so that a rail-to-rail voltage can be passed.
When the /CS1 voltage is low, Q3 will conduct. When the /CS1 voltage is high, Q4 con-
ducts. It takes time for the transistors to turn on, creating a propagation delay. This propa-
gation delay is typically very small, about 10 ns to 15 ns.
/CS1
/CSRAM
/RESET_OUT
Q3
Q4
R28
VRAM
100 kW
VRAM
SWITCH
相关PDF资料
PDF描述
11FMN-BMTR-A-TB CONN FMN HSNG 11POS SGL REV SMD
11FMN-BMT-A-TF CONN FMN HSNG 11POS SNGL NOR SMD
AT24C01-10SI-2.7 IC EEPROM 1KBIT 400KHZ 8SOIC
AT24C01-10PI-2.7 IC EEPROM 1KBIT 400KHZ 8DIP
20-101-1067 MODULE RABBITCORE RCM3305
相关代理商/技术参数
参数描述
101-0494 功能描述:模块化系统 - SOM RCM2250 RABBITCORE RoHS:否 制造商:Digi International 外观尺寸:ConnectCore 9P 处理器类型:ARM926EJ-S 频率:150 MHz 存储容量:8 MB, 16 MB 存储类型:NOR Flash, SDRAM 接口类型:I2C, SPI, UART 工作电源电压:3.3 V 最大工作温度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
101-0495 功能描述:处理器配件 Baseplate RoHS:否 制造商:Olimex Ltd. 产品:Cable 用于:
101-0497 功能描述:单板计算机 OP6810 RoHS:否 制造商:Ampro By ADLINK 外观尺寸:EPIC 处理器类型:Intel Atom D510 频率:1.66 GHz 存储容量:2 GB (max) 存储类型:DDR2, L2 Cache 接口类型:Ethernet, PS/2, SATA, Serial, USB 工作电源电压:5 V, 12 V 功耗:13 W 最大工作温度:+ 70 C 尺寸:165.1 mm x 114.3 mm
10104997-00C-10B 功能描述:高速/模块连接器 XCEDE 2W 6PVH 6COL RoHS:否 制造商:Molex 系列:iPass 产品类型: 排数: 列数: 位置/触点数量:38 安装角:Right 节距:0.8 mm 安装风格:Plug 端接类型:SMD/SMT 外壳材料:Thermoplastic 触点材料:High Performance Alloy (HPA) 触点电镀:Gold
10104997-00C-10DLF 功能描述:高速/模块连接器 XCEDE 2W 6PVH 6COL RoHS:否 制造商:Molex 系列:iPass 产品类型: 排数: 列数: 位置/触点数量:38 安装角:Right 节距:0.8 mm 安装风格:Plug 端接类型:SMD/SMT 外壳材料:Thermoplastic 触点材料:High Performance Alloy (HPA) 触点电镀:Gold