参数资料
| 型号： | 101-0589 |
| 厂商： | Rabbit Semiconductor |
| 文件页数： | 3/7页 |
| 文件大小： | 0K |
| 描述： | CLONING BOARD RABBIT |
| 标准包装： | 10 |
| 附件类型： | Rabbit 克隆板 |
| 适用于相关产品： | RabbitCore 模块 |
| 其它名称： | 316-1047 |
Steps to Perform Cloning
The Rabbit Cloning Board comes with 1.27 mm and 2 mm cables to accommodate whichever size of the
programming connector that is on your Rabbit-based board.
1. Use one of the 1.27 mm or 2 mm cables to connect the MASTER header (J3 or J1, depending on the
cable used) on the Cloning Board to the programming port of your master controller. Make sure that the
Figure 2. Cloning Cable Connections to the Rabbit Cloning Board
MASTER
MASTER
J1
CLONING BOARD
RABBIT CLONING
J2
TARGET
Colored side
UP
R1
2 mm
pitch
1.27 mm
pitch
J3
MASTER
RESET MASTER
S1
CLONE STATUS
DS1
J4
CLONE
2 mm
pitch
1.27 mm
pitch
Colored side
DOWN
175-0247 REV. A
TARGET
BEING
CLONED
2. Use the other cable to connect the CLONE header (J4 or J2) on the Cloning Board to the programming
port of the target controller. Make sure that the colored side of the cable goes to pin 1 of the header as
shown in Figure 2.
3. Apply power to both the master and the target.
4. Press the RESET MASTER button on the Rabbit Cloning Board to initiate cloning. The master begins
sending the designated portion of the primary flash to the clone.
The following table describes the LED patterns that may occur on the Cloning Board.
Table 1. LED Patterns on Cloning Board
Dynamic C
Cloning Status
Version
Up thru 7.06
Cloning is active
LED blinks several
times per second.
Cloning successfully completed
LED will blink quickly in a distinctive pattern of
four flashes, then pause, then four more flashes…
Error occurred
LED stops blinking.
7.05 thru 7.10
in fast
LED is off.
LED is on.
LED starts blinking.
cloning mode
Starting with LED toggles on and off
7.20 about once per second.
LED stays on.
LED starts blinking.
If an error occurs press the RESET MASTER button on the Cloning Board to try again.
TN207
3
相关PDF资料 |
PDF描述 |
|---|---|
| 101-0688 | CARD D/A EXPANSION RN1300 |
| 101-0954 | KIT DEV RABBIT RCM3360/3370 INTL |
| 101-1050-BE-00025 | ADPT USB 2 A FEMALE-2 5PIN .25M |
| 10112627-101LF | MINI-SAS HD 1X2 EXT PCB |
| 10112628-101LF | MINI-SAS HD 1X4 EXT PCB |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 101-0590 | 功能描述:模块配件 BL2010 Btm Mnt RoHS:否 制造商:Lantronix 产品: 用于: |
| 101-0591 | 功能描述:单板计算机 BL2010 Fri Lock RoHS:否 制造商:Ampro By ADLINK 外观尺寸:EPIC 处理器类型:Intel Atom D510 频率:1.66 GHz 存储容量:2 GB (max) 存储类型:DDR2, L2 Cache 接口类型:Ethernet, PS/2, SATA, Serial, USB 工作电源电压:5 V, 12 V 功耗:13 W 最大工作温度:+ 70 C 尺寸:165.1 mm x 114.3 mm |
| 101-0592 | 功能描述:单板计算机 BL2010 IDC Headers RoHS:否 制造商:Ampro By ADLINK 外观尺寸:EPIC 处理器类型:Intel Atom D510 频率:1.66 GHz 存储容量:2 GB (max) 存储类型:DDR2, L2 Cache 接口类型:Ethernet, PS/2, SATA, Serial, USB 工作电源电压:5 V, 12 V 功耗:13 W 最大工作温度:+ 70 C 尺寸:165.1 mm x 114.3 mm |
| 10105928-1 | 功能描述:环形MIL规格工具、五金与附件 RoHS:否 制造商:Amphenol Industrial MIL 类型:MIL-DTL-5015 系列:97 产品类型:Dummy Receptacles 用于:97 Series Plugs |
| 10105928-2 | 功能描述:环形MIL规格工具、五金与附件 RoHS:否 制造商:Amphenol Industrial MIL 类型:MIL-DTL-5015 系列:97 产品类型:Dummy Receptacles 用于:97 Series Plugs |
发布紧急采购，3分钟左右您将得到回复。