- 您现在的位置：买卖IC网 > PDF目录351527 > 101151038 STECKSTUTZEN EINSCHRAUB 10MM BSP 0.375 PDF资料下载
参数资料
| 型号： | 101151038 |
| 英文描述： | STECKSTUTZEN EINSCHRAUB 10MM BSP 0.375 |
| 中文描述： | STECKSTUTZEN EINSCHRAUB 10毫米BSP的0.375 |
| 文件页数： | 17/17页 |
| 文件大小： | 269K |
| 代理商： | 101151038 |
Philips Semiconductors Programmable Logic Devices
Product specification
10H20EV8/10020EV8
ECL programmable array logic
October 22, 1993
121
AC TEST CIRCUIT
PULSE
GENERATOR
SCOPE
RT
L1
L3
VCC
VCO1
VCO2
VEE
SCOPE
L2
RT
CL
I1
I11
CLK/I12
FM
FN
FX
FY
DUT
+2.0V + 0.010V
–2.5V + 0.010V FOR 10020EV8
–3.2V + 0.010V FOR 10H20EV8
25
F
0.01
F
NOTES:
1. Use decoupling capacitors of 0.1
F and 25F from GND to VCC, and 0.01F and 25F from GND to VEE (0.01 and 0.1F capacitors
should be NPO Ceramic or MLC type). Decoupling capacitors should be placed as close as physically possible to the DUT and lead
length should be kept to less than 1/4 inch (6mm).
2. All unused inputs should be connected to either HIGH or LOW state consistent with the LOGIC function required.
3. All unused outputs are loaded with 50
to GND.
4. L1 and L2 are equal length 50 impedance lines. L3, the distance from the DUT pin to the junction of the cable from the Pulse
Generator and the cable to the Scope, should not exceed 1/4 inch (6mm).
5. RT = 50 terminator internal to Scope.
6. The unmatched wire stub between coaxial cable and pins under test must be less than 1/4 inch (6mm) long for proper test.
7. CL = Fixture and stray capacitance ≤ 3pF.
8. Any unterminated stubs connected anywhere along the transmission line between the Pulse Generator and the DUT or between the
DUT and the Scope should not exceed 1/4 inch (6mm) in length (refer to section on AC setup procedure).
9. All 50
resistors should have tolerance of ± 1% or better.
10. Test procedures are shown for only one input or set of input conditions. Other inputs are tested in the same manner.
25
F
0.1
F
相关PDF资料 |
PDF描述 |
|---|---|
| 101151248 | STECKSTUTZEN EINSCHRAUB 12MM BSP 0.5 |
| 1012-0100 | MATRIX DRUCKER TRAGBAR SERIELL 24SPALTEN |
| 101-205-02 | LED SUBMIN PCB MNT RED |
| 101-205-20 | LED PCB MOUNT RED |
| 1012-105 | Analog IC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 10115104-1050011LF | 功能描述:高速/模块连接器 RoHS:否 制造商:FCI 系列: 产品类型: 排数: 列数: 位置/触点数量: 安装角: 节距: 安装风格: 端接类型: 外壳材料: 触点材料: 触点电镀: |
| 10-115114-02S | 制造商:Amphenol Aerospace 功能描述:RECEPT |
| 10-115114-05P | 制造商:Amphenol Aerospace 功能描述:RECEPT |
| 10-115114-05S | 制造商:Amphenol Aerospace 功能描述:RECEPT |
| 10-115114-08S | 制造商:Amphenol Aerospace 功能描述:RECEPT |
发布紧急采购，3分钟左右您将得到回复。