- 您现在的位置：买卖IC网 > PDF目录351528 > 101471048 EINSCHRAUBVERB WINKEL DREHBAR 10MM 0.5 PDF资料下载
参数资料
| 型号： | 101471048 |
| 英文描述： | EINSCHRAUBVERB WINKEL DREHBAR 10MM 0.5 |
| 中文描述： | EINSCHRAUBVERB克尔DREHBAR 10毫米0.5 |
| 文件页数： | 17/17页 |
| 文件大小： | 269K |
| 代理商： | 101471048 |
Philips Semiconductors Programmable Logic Devices
Product specification
10H20EV8/10020EV8
ECL programmable array logic
October 22, 1993
121
AC TEST CIRCUIT
PULSE
GENERATOR
SCOPE
RT
L1
L3
VCC
VCO1
VCO2
VEE
SCOPE
L2
RT
CL
I1
I11
CLK/I12
FM
FN
FX
FY
DUT
+2.0V + 0.010V
–2.5V + 0.010V FOR 10020EV8
–3.2V + 0.010V FOR 10H20EV8
25
F
0.01
F
NOTES:
1. Use decoupling capacitors of 0.1
F and 25F from GND to VCC, and 0.01F and 25F from GND to VEE (0.01 and 0.1F capacitors
should be NPO Ceramic or MLC type). Decoupling capacitors should be placed as close as physically possible to the DUT and lead
length should be kept to less than 1/4 inch (6mm).
2. All unused inputs should be connected to either HIGH or LOW state consistent with the LOGIC function required.
3. All unused outputs are loaded with 50
to GND.
4. L1 and L2 are equal length 50 impedance lines. L3, the distance from the DUT pin to the junction of the cable from the Pulse
Generator and the cable to the Scope, should not exceed 1/4 inch (6mm).
5. RT = 50 terminator internal to Scope.
6. The unmatched wire stub between coaxial cable and pins under test must be less than 1/4 inch (6mm) long for proper test.
7. CL = Fixture and stray capacitance ≤ 3pF.
8. Any unterminated stubs connected anywhere along the transmission line between the Pulse Generator and the DUT or between the
DUT and the Scope should not exceed 1/4 inch (6mm) in length (refer to section on AC setup procedure).
9. All 50
resistors should have tolerance of ± 1% or better.
10. Test procedures are shown for only one input or set of input conditions. Other inputs are tested in the same manner.
25
F
0.1
F
相关PDF资料 |
PDF描述 |
|---|---|
| 101471248 | EINSCHRAUBVERB WINKEL DREHBAR 12MM 0.5 |
| 10150 | PHOSPHORBRONZE TUBE 2X1ZOLL |
| 1015-105 | Analog IC |
| 1015-106 | Analog IC |
| 1015-112 | Analog IC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 101471248 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:EINSCHRAUBVERB WINKEL DREHBAR 12MM 0.5 |
| 101472T063BA2A | 功能描述:ALUM-SCREW TERMINAL 制造商:cornell dubilier electronics (cde) 系列:* 零件状态:新产品 标准包装:5 |
| 101472U025AA2B | 功能描述:ALUM-SCREW TERMINAL 制造商:cornell dubilier electronics (cde) 系列:* 零件状态:新产品 标准包装:5 |
| 101472U050AC1A | 功能描述:ALUM-SCREW TERMINAL 制造商:cornell dubilier electronics (cde) 系列:* 零件状态:新产品 标准包装:5 |
| 1014730000 | 功能描述:CONN TERM BLOCK 5.08MM 2POS BLK RoHS:是 类别:连接器，互连式 >> 接线座 - 接头，插头和插口 系列:Omnimate BLF 标准包装:1 系列:OSTVK 端接块类型:接头，公引脚，带罩（4 面） 每电平位置:18 间距:0.138"（3.50mm） 级别数目:1 接头定向:45° 插头导线入口:- 端子:焊接 线规:- 电流:8A 电压:300V 安装类型:通孔 特点:- 颜色:绿 包装:散装 配套产品:OSTVM181550-ND - TERM BLOCK PLUG 3.50MM 18POSOSTV7181151-ND - TERM BLOCK PLUG 3.50MM 18POSOSTV7181150-ND - TERM BLOCK PLUG 3.50MM 18POSOSTTS18115B-ND - TERM BLOCK PLUG 3.50MM 18POSOSTTS18115A-ND - TERM BLOCK PLUG 3.50MM 18POS |
发布紧急采购，3分钟左右您将得到回复。