- 您现在的位置：买卖IC网 > PDF目录12428 > 10180-6000EC (3M)CONN MDR PLUG 80POS IDC GOLD PDF资料下载
参数资料
| 型号： | 10180-6000EC |
| 厂商： | 3M |
| 文件页数： | 2/6页 |
| 文件大小： | 0K |
| 描述： | CONN MDR PLUG 80POS IDC GOLD |
| 其它有关文件： | MDR Selection Guide |
| 产品培训模块： | Input/Output Connector Systems Primer Mini Delta Ribbon Connector System |
| 视频文件： | MDR System |
| 产品目录绘图： | 101xx-6000EC Series |
| 标准包装： | 100 |
| 系列： | 101, Mini D Ribbon (MDR) |
| 连接器类型： | 中央带触点 |
| 连接器类型： | 插头 |
| 位置数： | 80 |
| 行数： | 2 |
| 安装类型： | 自由悬挂 |
| 端子： | IDC |
| 特点： | 屏蔽 |
| 触点表面涂层： | 金 |
| 触点涂层厚度： | 30µin（0.76µm） |
| 产品目录页面： | 51 (CN2011-ZH PDF) |
| 配套产品： | N10280-52E2PC-ND - CONN MINI-D 80POS R/A RECPT N10280-52B2PC-ND - CONN MINI-D 80POS R/A RECPT N10280-5242PC-ND - CONN MINI-D 80POS R/A RECPT 3M1830-ND - CONN MDR RECPT 80POS VERT T/H 3M1738-ND - CONN MDR RCPT 80POS VERT T/H |
| 相关产品： | 3M3829-ND - TOOL HAND FOR MINI-D PLUG |
| 其它名称： | 101806000EC 4901690086458 90169008645 JE150174918 MPB80A |
6.
Locate cutting unit stop brackets and thumbscrew (D & E
of Fig. 4). Depending on size of assembly choose
7.
8.
Push platen back into place using the side bar.
After installing the stop bracket, position the armature
stop bracket accordingly.
(Black for 14-50 position and Silver for 68-100 position.)
Stop brackets are installed using the thumbscrew
(A & B of Fig. 2).
of the press back in an upright position. Tighten the
thumbscrew (C of Fig. 2) to hold it in place.
9. Located at the back of the press is a silver, dowel shaped
shuttle stop (D of Fig. 2). Set shuttle stop for appropriate
connector pin count.
10. Locate the shuttle block (C of Fig. 4) and install fixture
unit (Fig. 14) on the guide pins. Push the release buttons
on the front of the fixture unit to open the grooved plates.
11. Locate the gauge block (F of Fig. 4). Height adjustment
can be accomplished by placing the gauge block, narrow
side down, in the fixture unit between the two grooved
plates. Close plates manually by squeezing
them together.
B
A
5
Figure 5. 10961 Cutting Unit
Figure 3. Press leaned back
B.
Side bar
A.
Height
adjustment
knob
3
12. Push shuttle, with fixture unit and gauge block, away
from the operator to the rear of the press until it stops.
13. Pull the press handle down, toward the operator, until
the platen contacts the gauge block.
DO NOT FORCE HANDLE.
14. Adjust the silver knob at the top of the press (A of Fig. 4)
by hand until the platen lightly contacts the gauge block.
Lift press handle up and adjust the silver knob
approximately another one-half turn tighter. Pull handle
down again. It should lightly lock in place when fully
depressed. The platen should apply enough pressure
on the gauge block and shuttle to prevent them from
moving when trying to slide them out.
15. Height adjustment should be checked periodically.
Fixture Unit Adjustment
knob &
platen
C.
Shuttle
block
Once the size of the connector to be assembled has been
determined the 10962 Fixture Unit requires some adjustments.
E.
Thumbscrew
D.
Stop brackets
F.
Gauge block
1.
2.
Select the correct connector stop (14, 20, 26, 36, 40, 50,
68, 80 or 100 position; B of Fig. 14) for your application.
Locate the yolk shaped cover plate (A of Fig. 14) and
thumbscrew at the top of the fixture unit. Remove
and set aside. Close fixture unit grooved plates by
manually squeezing them together.
4
Figure 4. 10960-2000 Hand Press
2
相关PDF资料 |
PDF描述 |
|---|---|
| 10226-0210EC | CONN MDR RECPT 26POS IDC GOLD |
| 10150-3000PE | CONN MDR PLUG 50POS SLD CUP |
| 10226-2210PE | CONN MINI-D 26POS R/A RECPT |
| 12226-5150-00FR | CONN SDR 26POS R/A RECEPT |
| 10226-2200PE | CONN MINI-D 26POS VERT RECPT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 10180-6000EL | 制造商:3M Electronic Products Division 功能描述: |
| 10180740 | 功能描述:环形MIL规格后盖 RoHS:否 制造商:Amphenol PCD MIL 类型:MIL-DTL-38999 III, IV 系列:AS85049 产品类型:Environmental EMI/RFI Backshells 外壳类型:Straight 外壳大小:18 外壳材质:Aluminum Alloy |
| 10180-BK | 制造商:Datak Corporation 功能描述: |
| 10180-BU | 制造商:Datak Corporation 功能描述: |
| 10180F | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Dual 2-Bit Adder/Subtractor |
发布紧急采购，3分钟左右您将得到回复。