- 您现在的位置：买卖IC网 > PDF目录68751 > 1023RD2E-25TE13 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, DSO8 PDF资料下载
参数资料
| 型号： | 1023RD2E-25TE13 |
| 元件分类： | 电源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, DSO8 |
| 封装： | 3 X 4.90 MM, 0.80 MM HEIGHT, EXPOSED PAD, MSOP FOOTPRINT, TDFN-8 |
| 文件页数： | 17/17页 |
| 文件大小： | 107K |
| 代理商： | 1023RD2E-25TE13 |
9
Preliminary Information
CAT1021, CAT1022, CAT1023
Doc No. 3009, Rev. E
EMBEDDED EEPROM OPERATION
The CAT1021/22/23 feature a 2kbit embedded serial
EEPROM that supports the I2C Bus data transmission
protocol. This Inter-Integrated Circuit Bus protocol defines
any device that sends data to the bus to be a transmitter
and any device receiving data to be a receiver. The
transfer is controlled by the Master device which
generates the serial clock and all START and STOP
conditions for bus access. Both the Master device and
Slave device can operate as either transmitter or receiver,
but the Master device controls which mode is activated.
I2C Bus Protocol
The features of the I2C bus protocol are defined as
follows:
(1) Data transfer may be initiated only when the bus is
not busy.
(2) During a data transfer, the data line must remain
stable whenever the clock line is high. Any changes in
the data line while the clock line is high will be interpreted
as a START or STOP condition.
START Condition
The START Condition precedes all commands to the
device, and is defined as a HIGH to LOW transition of
SDA when SCL is HIGH. The CAT1021/22/23 monitor
the SDA and SCL lines and will not respond until this
condition is met.
STOP Condition
A LOW to HIGH transition of SDA when SCL is HIGH
determines the STOP condition. All operations must end
with a STOP condition.
DEVICE ADDRESSING
The Master begins a transmission by sending a START
condition. The Master sends the address of the particular
slave device it is requesting. The four most significant
bits of the 8-bit slave address are programmable in metal
and the default is 1010.
The last bit of the slave address specifies whether a
Read or Write operation is to be performed. When this bit
is set to 1, a Read operation is selected, and when set
to 0, a Write operation is selected.
After the Master sends a START condition and the slave
address byte, the CAT1021/22/23 monitors the bus and
responds with an acknowledge (on the SDA line) when
its address matches the transmitted slave address. The
CAT1021/22/23 then perform a Read or Write operation
depending on the R/
W bit.
tWR
STOP
CONDITION
START
CONDITION
ADDRESS
ACK
8TH BIT
BYTE n
SCL
SDA
Figure 4. Write Cycle Timing
tHIGH
SCL
SDA IN
SDA OUT
tLOW
tF
tLOW
tR
tBUF
tSU:STO
tSU:DAT
tHD:DAT
tHD:STA
tSU:STA
tAA
tDH
Figure 3. Bus Timing
相关PDF资料 |
PDF描述 |
|---|---|
| 1023RD4E-30TE13 | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, DSO8 |
| 1023RE-30TE13 | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| 1023RI-45TE13 | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| 1022LI-30TE13 | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDIP8 |
| 1022LE-42TE13 | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDIP8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 1023-T12 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:DECODED MAGNETIC STRIPE READER TRACK1 &2 |
| 1023-T123 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:DECODED MAGNETIC STRIPE READ TRACK 1 2 3 |
| 1023-T2 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:DECODED MAGNETIC STRIPE READER TRACK2 |
| 1024 | 功能描述:电池座、电池扣和电池接头 AA Battery Holder SMT RoHS:否 制造商:Eagle Plastic Devices 产品:Battery Snaps 电池组电池大小:9 V 电池数量:1 端接类型:Snaps 颜色:Black 材料:Polyvinyl Chloride (PVC) 安装风格:Snap-In |
| 10-24 AJ 6 | 功能描述:螺丝和紧固件 SEELNUTS 10-24 THREAD RoHS:否 制造商:Unspecified 产品: 类型:Washer 螺纹大小: 长度: 材料:Steel 电镀:Nickel 螺丝头: 螺丝类型: |
发布紧急采购，3分钟左右您将得到回复。