- 您现在的位置：买卖IC网 > PDF目录62887 > 103114 SCHRAUBENSICHERUNG 10ML PDF资料下载
参数资料
| 型号： | 103114 |
| 英文描述： | SCHRAUBENSICHERUNG 10ML |
| 中文描述： | SCHRAUBENSICHERUNG毫升 |
| 文件页数： | 2/2页 |
| 文件大小： | 31K |
| 代理商： | 103114 |
TDS 222, October 1995
Loctite is a Registered Trademark of Loctite Corporation, Hartford, CT 06106
PERFORMANCE OF CURED MATERIAL
(After 24 hr at 22
°C on M10 steel nuts & bolts)
Typical
Value
Range
Breakaway Torque, ISO 10964, N.m
6
3 to 9
(lb.in)
(53)
(25 to 80)
Prevail Torque, ISO 10964, N.m
4
1 to 6
(lb.in)
(30)
(10 to 50)
Breakloose Torque, DIN 54454, N.m
14
8 to 20
(lb.in)
(120)
(71 to 180)
Max. Prevail Torque, DIN 54454, N.m
14
8 to 20
(lb.in)
(120)
(71 to 180)
TYPICAL ENVIRONMENTAL RESISTANCE
Test Procedure :
Breakloose Torque, DIN 54454
Substrate:
M10 Zinc Phosphate Nuts & Bolts
Cure procedure:
1 week at 22
°C
Hot Strength
Tested at temperature.
0
50
100
150
0
25
50
75
100
%
R
T
Strengt
h
Temperature, °C
Heat Aging
Aged at temperature indicated and tested at 22°C.
0
1,000
2,000
3,000
4,000
5,000
0
25
50
75
100
125
Hours
%
Ini
ti
a
l
S
trength
at
R
T
120°C
150°C
Chemical / Solvent Resistance
Aged under conditions indicated and tested at 22°C.
Solvent
Temp
.
% Initial Strength retained at
100
hr
500
hr
1000 hr
5000 hr
Motor Oil
125
°
C
100
95
90
85
Leaded Petrol
22
°C
95
Brake Fluid
22
°C
95
90
Water/Glycol
(50%/50%)
87
°C
80
Ethanol
22
°C
95
90
Acetone
22
°C
100
90
GENERAL INFORMATION
This product is not recommended for use in pure oxygen
and/or oxygen rich systems and should not be selected as a
sealant for chlorine or other strong oxidising materials.
For safe handling information on this product, consult the
Material Safety Data Sheet, (MSDS).
Where aqueous washing systems are used to clean the
surfaces before bonding, it is important to check for compatibility
of the washing solution with the adhesive. In some cases these
aqueous washes can affect the cure and performance of the
adhesive.
This product is not normally recommended for use on plastics
(particularly thermoplastic materials where stress cracking of
the plastic could result).
Users are recommended to confirm
compatibility of the product with such substrates.
Directions for use
For best performance surfaces should be clean and free of
grease. Product should be applied to the bolt in sufficient
quantity to fill all engaged threads. This product performs best in
thin bond gaps, (0.05mm). Very large thread sizes may create
large gaps which will affect
cure speed and strength. This
product is designed to give controlled friction, (torque/tension
ratio), during assembly. In critical tightening applications this
ratio should be confirmed.
Storage
Product shall be ideally stored in a cool, dry location in
unopened containers at a temperature between 8
°C to 28°C
(46
°F to 82°F) unless otherwise labelled. Optimal storage is at
the lower half of this temperature range.
To prevent
contamination of unused product, do not return any material to
its original container. For further specific shelf life information,
contact your local Technical Service Centre.
Data Ranges
The data contained herein may be reported as a typical value
and/or range (based on the mean value
±2 standard deviations).
Values are based on actual test data and are verified on a
periodic basis.
Note
The data contained herein are furnished for information only and
are believed to be reliable. We cannot assume responsibility for
the results obtained by others over whose methods we have no
control. It is the user's responsibility to determine suitability for
the user's purpose of any production methods mentioned herein
and to adopt such precautions as may be advisable for the
protection of property and of persons against any hazards that
may be involved in the handling and use thereof. In light of the
foregoing,
Loctite
Corporation
specifically
disclaims
all
warranties
expressed
or
implied,
including
warranties
of
merchantability or fitness for a particular purpose, arising from
sale or use of
Loctite
Corporation’s
products.
Loctite
Corporation specifically disclaims any liability for consequential
or incidental damages of any kind, including lost profits. The
discussion herein of various processes or compositions is not to
be interpreted as representation that they are free from
domination of patents owned by others or as a license under
any Loctite Corporation patents that may cover such processes
or compositions.
We recommend that each prospective user
test his proposed application before repetitive use, using this
data as a guide. This product may be covered by one or more
United States or foreign patents or patent applications.
相关PDF资料 |
PDF描述 |
|---|---|
| 10315 | DESCALER HEATING SYSTEM 5LTR |
| 10316 | DESCALER HEATING SYSTEM 25LTR |
| 103166-1 | 6 WAY RIGHT ANGLE DOUBLE |
| 103166-2 | STIFTLEISTE MIT GEHAEUSE HOR 2X3POL |
| 103166-3 | STIFTLEISTE MIT GEHAEUSE HOR 2X4POL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 10-311-4-01 | 制造商:Concord Electronics Inc 功能描述: |
| 1031-18 | 制造商:Bahco 功能描述:Bulk |
| 10-31-188-122 | 制造商:Texas Instruments 功能描述: |
| 10311-ER | 功能描述:PLIERS CHAIN NOSE XL SMOOTH ERG RoHS:否 类别:工具 >> 钳子、扳手 系列:- 标准包装:1 系列:- 尖端 - 类型:针头，直形 工具类型:钳子 特点:人机工程型手柄，ESD 安全，锯齿状 长度:5.75"（146.05mm） 重量:0.23 磅（104.33g） |
| 10311S | 功能描述:PLIERS CHAIN NOSE XL SERRATE STD RoHS:否 类别:工具 >> 钳子、扳手 系列:- 标准包装:1 系列:- 尖端 - 类型:针头，直形 工具类型:钳子 特点:人机工程型手柄，ESD 安全，锯齿状 长度:5.75"（146.05mm） 重量:0.23 磅（104.33g） |
发布紧急采购，3分钟左右您将得到回复。