- 您现在的位置：买卖IC网 > PDF目录19042 > 10962-2000 (3M)LACING FIXTURE UNIT MDR PDF资料下载
参数资料
| 型号： | 10962-2000 |
| 厂商： | 3M |
| 文件页数： | 2/6页 |
| 文件大小： | 0K |
| 描述： | LACING FIXTURE UNIT MDR |
| 标准包装： | 1 |
| 系列： | MDR |
| 附件类型： | 线束固定手压机 |
| 适用于相关产品： | MDR 线装式插头 |
| 其它名称： | 05113832693 80610714653 |
6.
Locate cutting unit stop brackets and thumbscrew (D & E
of Fig. 4). Depending on size of assembly choose
7.
8.
Push platen back into place using the side bar.
After installing the stop bracket, position the armature
stop bracket accordingly.
(Black for 14-50 position and Silver for 68-100 position.)
Stop brackets are installed using the thumbscrew
(A & B of Fig. 2).
of the press back in an upright position. Tighten the
thumbscrew (C of Fig. 2) to hold it in place.
9. Located at the back of the press is a silver, dowel shaped
shuttle stop (D of Fig. 2). Set shuttle stop for appropriate
connector pin count.
10. Locate the shuttle block (C of Fig. 4) and install fixture
unit (Fig. 14) on the guide pins. Push the release buttons
on the front of the fixture unit to open the grooved plates.
11. Locate the gauge block (F of Fig. 4). Height adjustment
can be accomplished by placing the gauge block, narrow
side down, in the fixture unit between the two grooved
plates. Close plates manually by squeezing
them together.
B
A
5
Figure 5. 10961 Cutting Unit
Figure 3. Press leaned back
B.
Side bar
A.
Height
adjustment
knob
3
12. Push shuttle, with fixture unit and gauge block, away
from the operator to the rear of the press until it stops.
13. Pull the press handle down, toward the operator, until
the platen contacts the gauge block.
DO NOT FORCE HANDLE.
14. Adjust the silver knob at the top of the press (A of Fig. 4)
by hand until the platen lightly contacts the gauge block.
Lift press handle up and adjust the silver knob
approximately another one-half turn tighter. Pull handle
down again. It should lightly lock in place when fully
depressed. The platen should apply enough pressure
on the gauge block and shuttle to prevent them from
moving when trying to slide them out.
15. Height adjustment should be checked periodically.
Fixture Unit Adjustment
knob &
platen
C.
Shuttle
block
Once the size of the connector to be assembled has been
determined the 10962 Fixture Unit requires some adjustments.
E.
Thumbscrew
D.
Stop brackets
F.
Gauge block
1.
2.
Select the correct connector stop (14, 20, 26, 36, 40, 50,
68, 80 or 100 position; B of Fig. 14) for your application.
Locate the yolk shaped cover plate (A of Fig. 14) and
thumbscrew at the top of the fixture unit. Remove
and set aside. Close fixture unit grooved plates by
manually squeezing them together.
4
Figure 4. 10960-2000 Hand Press
2
相关PDF资料 |
PDF描述 |
|---|---|
| OPF-L | OPTIC LENS FLARE LUX 10X80DEG |
| OP-FL | FLARE LENS FOR LUXEON 10 X 80DEG |
| 3502-AG5-2 | TOOL DIE CRIMP FOR IL-AG5 SERIES |
| OPT-L3WSL | SUB-LENS TRIPLE SPOT WIDE |
| OPA-A3WSL | SUB-LENS TRIPLE WIDE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 109622-001 | 制造商:FCI 功能描述:WIRE BARREL CRIMPER |
| 1096232 | 制造商:NATIONAL AEROSPACE STANDA 功能描述: |
| 1096-2-32 | 制造商: 功能描述: 制造商:undefined 功能描述: |
| 109623-2 | 制造商:TE Connectivity 功能描述:HSG W/LOCKS, 10-WAY,AUTOSYSTEM |
| 109624-1 | 功能描述:汽车连接器 HOUSING, LO-BEAM, AUTOSYSTEMS RoHS:否 制造商:Amphenol SINE Systems 产品:Contacts 系列:ATP 位置数量: 型式:Female 安装风格: 端接类型: 触点电镀:Nickel |
发布紧急采购，3分钟左右您将得到回复。