- 您现在的位置：买卖IC网 > PDF目录11501 > 127-2701-602 (Emerson Network Power Connectivity Johnson)CONN SMP SHROUD MALE FLANGE MT PDF资料下载
参数资料
| 型号： | 127-2701-602 |
| 厂商： | Emerson Network Power Connectivity Johnson |
| 文件页数： | 16/20页 |
| 文件大小： | 0K |
| 描述： | CONN SMP SHROUD MALE FLANGE MT |
| 产品目录绘图： | 127-(0,1,2)701-602 |
| 特色产品： | SMP Blind-Mate Connectors |
| 标准包装： | 5 |
| 系列： | SMP |
| 附件类型： | 体座 |
| 适用于相关产品： | SMP 连接器 |
| 特点： | 法兰安装（2 孔），平滑孔 |
| 其它名称： | J10013 |
Connectivity for
SMP Connectors
Assembly Instructions
SMP Straight Female Solder Style for .086 OD Semi-Rigid Cable
1. Identify tools (6 piece parts) and connector parts (2 piece parts).
2. Strip cable jacket and dielectric to dimension shown. Do not
nick center conductor. Clean all debris from prepared cable.
3. Place contact onto center conductor, insert solder shim between
cable jacket and contact.
4. Insert contact into contact holder fixture and clamp cable in vise.
Tighten stop screw until light pressure is applied between con-
tact, solder shim and cable jacket.
5. Solder contact to center conductor through solder hole using
.016 (0.41) diameter flux core solder wire or solder paste. Use a
minimum amount of solder and heat for a good joint. Do not
allow heat to build up for a long period of time as cable dielectric
will expand.
6. After solder joint has cooled, remove solder shim and cable from
vise. Remove any excess solder from contact with a sharp blade
and clean all debris from contact and cable.
7. Insert contact into connector assembly, making sure cable
jacket bottoms out against internal shoulder of connector body.
Insert connector assembly into interface location fixture and
clamp cable in vise. Make sure connector assembly is fully en-
gaged within location fixture. Tighten stop screw until light pres-
sure is applied between connector assembly and cable jacket.
8. Solder end of connector body to cable jacket, using a minimum
amount of solder and heat for a full fillet joint. Allow assembly to
cool before removing connector from vise and location fixture.
Best results are obtained when contact location is flush to .004
(0.10) recessed from reference plane. Interface location fixture
is pre-set at factory, but can be adjusted to control location.
Business-Critical Continuity
Cable Group
RG-405, .086 Semi-Rigid
Tool
Cable Vise
Stop Screw
Clamp Inserts
Solder Shim
Contact Holder
Interface Location Fixture
16
Part Number
127-0693-001
Part Number
140-0000-962
140-0000-981
140-0000-964
140-0000-984
127-0000-902
127-0000-903
相关PDF资料 |
PDF描述 |
|---|---|
| PIC16C770T-I/SO | IC MCU OTP 2KX14 A/D PWM 20SOIC |
| VI-24F-IY-B1 | CONVERTER MOD DC/DC 72V 50W |
| VI-B33-CU-F1 | CONVERTER MOD DC/DC 24V 200W |
| VI-24B-IY-B1 | CONVERTER MOD DC/DC 95V 50W |
| VI-21Z-IY-B1 | CONVERTER MOD DC/DC 2V 20W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 127-2701-612 | 功能描述:RF 连接器 Rugged .012 pin 2 hole flange;Male SB RoHS:否 制造商:Bomar Interconnect 产品:Connectors 射频系列:BNC 型式:Jack (Female) 极性: 触点电镀:Gold 阻抗: 端接类型:Solder 主体类型:Straight Bulkhead 电缆类型: |
| 127-2701-801 | 功能描述:RF 连接器 End Launch male surface mnt SB RoHS:否 制造商:Bomar Interconnect 产品:Connectors 射频系列:BNC 型式:Jack (Female) 极性: 触点电镀:Gold 阻抗: 端接类型:Solder 主体类型:Straight Bulkhead 电缆类型: |
| 127270FB | 制造商:SUYIN-USA 制造商全称:SUYIN-USA 功能描述:L.C.D CONNECTOR |
| 127270-HMC765LP6CE | 功能描述:HMC765LP6CE - Timing, PLL Evaluation Board 制造商:analog devices inc. 系列:- 零件状态:有效 主要用途:计时，PLL 嵌入式:否 使用的 IC/零件:HMC765LP6CE 主要属性:带 VCO 的单路分数-N PLL 辅助属性:- 所含物品:板 标准包装:1 |
| 127271 | 制造商:Brady Corporation 功能描述:B302 10X14 RED/WHT IN CASE OF EMERGENCY |
发布紧急采购，3分钟左右您将得到回复。