- 您现在的位置：买卖IC网 > PDF目录11534 > 127-2901-822 (Emerson Network Power Connectivity Johnson)CONN ADAPTER MALE CM-MALE SB PDF资料下载
参数资料
| 型号： | 127-2901-822 |
| 厂商： | Emerson Network Power Connectivity Johnson |
| 文件页数： | 14/20页 |
| 文件大小： | 0K |
| 描述： | CONN ADAPTER MALE CM-MALE SB |
| 特色产品： | SMP Blind-Mate Connectors |
| 标准包装： | 5 |
| 适配器类型： | 插头至插头 |
| 适配器系列： | SMP 至 SMP |
| 中心类型： | 公型至公型 |
| 转换源（适配器端）： | SMP 公形 CM |
| 转换到（适配器端）： | SMP 公形 SB |
| 转换类型： | 相同系列 |
| 阻抗： | 50 欧姆 |
| 样式： | 直形 |
| 安装类型： | 自由悬挂 |
| 产品目录页面： | 466 (CN2011-ZH PDF) |
| 其它名称： | J10033 |
Connectivity for
SMP Connectors
Assembly Instructions
ASSEMBLY INSTRUCTIONS
SMP Straight Female Solder Style for .047 OD Semi-Rigid Cable
1 Identify tools (5 piece parts) and connector parts (3 piece parts).
2. Strip cable jacket and dielectric to dimension shown. Do not
nick center conductor. Clean all debris from prepared cable.
3. Insert center conductor into cable stop as shown and place
contact onto center conductor.
4. Insert contact into contact holder fixture and clamp cable in vise.
Tighten stop screw until light pressure is applied between con-
tact, cable stop and cable jacket.
5. Solder contact to center conductor through solder hole using
.016 (0.41) diameter flux core solder wire or solder paste. Use a
minimum amount of solder and heat for a good joint. Do not
allow heat to build up for a long period of time as cable stop
may melt.
6. After solder joint has cooled, remove cable from vise. Remove
any excess solder from contact with a sharp blade and clean all
debris from contact and cable.
7. Insert contact into connector assembly, making sure cable stop
bottoms out against internal shoulder of connector body. Insert
connector assembly into interface location fixture and clamp
cable in vise. Make sure connector assembly is fully engaged
within location fixture. Tighten stop screw until light pressure is
applied between connector assembly and cable stop.
8. Solder end of connector body to cable jacket, using a minimum
amount of solder and heat for a full fillet joint. Allow assembly to
cool before removing connector from vise and location fixture.
Best results are obtained when contact location is flush to .004
(0.10) recessed from reference plane. Interface location fixture
is pre-set at factory, but can be adjusted to control location.
Business-Critical Continuity
Cable Group
MIL-C-17/151, .047 Semi-Rigid
Tool
Cable Vise
Stop Screw
Clamp Inserts
Contact Holder
Interface Location Fixture
14
Part Number
127-0692-001
Part Number
140-0000-962
140-0000-981
140-0000-997
127-0000-902
127-0000-903
相关PDF资料 |
PDF描述 |
|---|---|
| VI-BWR-IY-B1 | CONVERTER MOD DC/DC 7.5V 50W |
| MS-145-HRMP-A | CONN ADAPT MS-145/SMA MALE |
| VI-BWP-IY-B1 | CONVERTER MOD DC/DC 13.8V 50W |
| VI-BWM-IY-B1 | CONVERTER MOD DC/DC 10V 50W |
| W2L1YC104KAT1A | CAP CER 0.1UF 16V 10% X7R 0508 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 127292-1 | 功能描述:手工工具 EXTENSION SPRING RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 127293 | 制造商:Brady Corporation 功能描述:B555 10X14 RED/WHT MAIN SPRINKLER VALVE |
| 127293-1 | 功能描述:手工工具 RETAINING RING RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 127294 | 制造商:Brady Corporation 功能描述:B401 10X14 RED/WHT MAIN SPRINKLER VALVE |
| 127295 | 制造商:Brady Corporation 功能描述:B302 10X14 RED/WHT MAIN SPRINKLER VALVE |
发布紧急采购，3分钟左右您将得到回复。