- 您现在的位置：买卖IC网 > PDF目录11739 > 127-3701-201 (Emerson Network Power Connectivity Johnson)CONN SMP RCPT MALE STR PC MOUNT PDF资料下载
参数资料
| 型号： | 127-3701-201 |
| 厂商： | Emerson Network Power Connectivity Johnson |
| 文件页数： | 17/20页 |
| 文件大小： | 0K |
| 描述： | CONN SMP RCPT MALE STR PC MOUNT |
| 产品目录绘图： | 127-(0,1,2,3)701-201 |
| 特色产品： | SMP Blind-Mate Connectors |
| 标准包装： | 5 |
| 系列： | SMP |
| 连接器类型： | SMP |
| 连接器类型： | 插座，公形引脚 |
| 阻抗： | 50 欧姆 |
| 安装类型： | 通孔 |
| 紧固型： | 推挽式 |
| 频率 - 最大： | 12GHz |
| 包装： | 散装 |
| 产品目录页面： | 466 (CN2011-ZH PDF) |
| 其它名称： | J10007 |
Connectivity for
Business-Critical Continuity
SMP Connectors
Assembly Instructions
SMP Right Angle Female Solder Style for .086 OD Semi-Rigid Cable
1. Identify tools (5 piece parts) and connector parts (2 piece parts).
2. Strip cable jacket and dielectric to dimension shown. Do not
nick center conductor. Clean all debris from prepared cable.
3. Make sure slot in connector contact is aligned with cross hole in
body as shown. Insert cable into cross hole in connector body,
making sure cable jacket bottoms out against internal shoulder
of connector body.
4. Insert connector assembly into interface location fixture and
clamp cable in vise using body holder fixture as shown. Tighten
stop screw until light pressure is applied between connector
body and cable jacket.
5. Solder contact to center conductor through rear access port in
connector body using a minimum amount of solder and heat for a
good joint. Do not allow solder to build up along exposed center
conductor.
6. After center conductor solder joint has cooled, solder connector
body to cable jacket, using a minimum amount of solder and heat
for a full fillet joint. Take care so that solder does not flow onto
anti-rock ring or into rear access port. Allow assembly to cool
before removing connector from vise and location fixture.
7. Using a fixture plate as shown, press end cap into rear access
port using a .156 (3.96) diameter flat punch until fully seated
within body counter bore.
8. Best results are obtained when contact location is flush to .004
(0.10) recessed from reference plane. Interface location fixture
is pre-set at factory, but can be adjusted to control location.
Cable Group
RG-405, .086 Semi-Rigid
Tool
Cable Vise
Stop Screw
Clamp Inserts
Body Holder
Interface Location Fixture
Part Number
127-0693-101
Part Number
140-0000-962
140-0000-981
140-0000-964
127-0000-904
127-0000-903
17
相关PDF资料 |
PDF描述 |
|---|---|
| VI-B4B-IW-F3 | CONVERTER MOD DC/DC 95V 100W |
| DS2406P+T&R | IC SW DL ADDRESS W/1K MEM 6-TSOC |
| 142-0761-821 | CONN JACK SMA 50 OHMS PC MOUNT |
| MS27484E18F35P | CONN PLUG 66POS STRAIGHT W/PINS |
| PIC16C67-20I/P | IC MCU OTP 8KX14 PWM 40DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 127-3701-602 | 功能描述:RF 连接器 Shroud 2 hole flange .235 wide CM RoHS:否 制造商:Bomar Interconnect 产品:Connectors 射频系列:BNC 型式:Jack (Female) 极性: 触点电镀:Gold 阻抗: 端接类型:Solder 主体类型:Straight Bulkhead 电缆类型: |
| 127371 | 制造商:Brady Corporation 功能描述:B555 10X14 BLK/RED/WHT WARNING EVACUATE |
| 127-37-1 | 制造商:WINCHESTER 制造商全称:Winchester Electronics Corporation 功能描述:RCPT PNL TNC |
| 127-37-2 | 制造商:WINCHESTER 制造商全称:Winchester Electronics Corporation 功能描述:RCPT PNL TNC |
| 127373 | 制造商:Brady Corporation 功能描述:B302 10X14 BLK/RED/WHT WARNING EVACUATE |
发布紧急采购，3分钟左右您将得到回复。