- 您现在的位置：买卖IC网 > Datasheet目录593 > 1320142-1 (TE Connectivity)SEAT TOOL BLINDMATE EXT.HEIGHT Datasheet资料下载
参数资料
| 型号： | 1320142-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/4页 |
| 文件大小： | 0K |
| 描述： | SEAT TOOL BLINDMATE EXT.HEIGHT |
| 标准包装： | 1 |
| 系列： | * |
408- 4328
!
!
3.2. Application Tooling
Power for seating tools must be provided by a
machine capable of supplying a downward force of
20 Newtons (N) [5 lb] per contact. 10/20--Ton “H”
Frame Assembly 803880--6 (Customer Manual
409--5567 provides instructions), SM--3 Frame
Assembly 814700--2 (409--5626), or Greenerd G
Frame Assemblies 3A and 3B equipped with Adapter
Kit (408--9027) can be used.
4. SEATING
When setting up equipment to seat connectors, pay
particular attention to the following:
S The seating tool must be matched to the
connector
S The seating tool, connector, and applicator ram
must be properly aligned before cycling the tool
CAUTION If the tool and connector are mismatched or are
improperly aligned, damage could occur to the
tooling, connector, or both.
1. Set seating height to the dimension shown in
Figure 2 (applicator shut height will equal the
seating height PLUS the combined thicknesses of
the pc board and pc board support).
2. Position connector onto pc board so that the
connector contacts are properly aligned to the pc
board and pc board support fixture.
3. Insert connector into pc board until the contacts
are resting securely on, but have not fully entered,
the board.
4. Position the seating tool on the connector,
making sure that the tool is bottomed on the
housing floor.
5. Center the seating tool and connector under the
applicator ram of the tool. Lower the ram slowly
until it just meets the seating tool. Verify alignment
of pc board support, pc board, connector, and
seating tool.
CAUTION Damage to the pc board, seating tool, or
connector may occur if seating height is
improperly set or if tool is not properly seated in
the connector before cycling the tool.
6. Cycle the tool to seat the connector in the pc
board. Then retract the ram and carefully remove
the seating tool. Check assembly for proper
seating according to Application Specification
114--6061.
7. Repeat Steps 2 through 6 until all the
connectors are seated.
View After Seating
Applicator Ram
(Fully Down)
Seating Tool Centered
Under Applicator Ram and
Bottomed on Connector
Applicator
Shut Height
(Ram Fully Down)
(See Section 4, Step 1)
Seating Height
(Connector Seated)
38.1+0.25/-- 0.00 mm
[1.50+.010/-- .000 in.]
Connector Contacts Inserted
into Holes in PC Board and
PC Board Support Fixture
PC Board
PC Board Support
Fixture (Ref)
Note: Not to Scale
G Trademark of Greenerd Press & Machine Co., Inc.
2 of 4
Figure 2
Rev C
相关PDF资料 |
PDF描述 |
|---|---|
| 1320369-1 | TOOL CRIMPING HEAD 8AWG COPALUM |
| 1320447-1 | TOOL DIE ASSY 2AWG BREAKAWAY |
| 1338273-1 | TOOL DIE ASSY 22-16AWG SOLIS |
| 1366402-1 | TOOL HAND 18-22AWG STR ACTION |
| 1366865-1 | EXT-TOOL FOR 025 TAB CONTACT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 1320142-2 | 功能描述:手工工具 RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 1320-148 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
| 132015 | 制造商:Brady Corporation 功能描述:B401 PLASTIC BLK,RED/WHT 7X10 |
| 132015-0073 | 功能描述:CONN INLINE PLUG HSG 16POS 制造商:itt cannon, llc 系列:CTC 包装:散装 零件状态:在售 连接器类型:插头 触头类型:母形插口 针脚数:16 间距:- 排数:4 排距:- 安装类型:自由悬挂 触头端接:压接 紧固类型:销锁 颜色:黑色 特性:密封式 备注:不含触头 标准包装:50 |
| 132015-0074 | 功能描述:CONN INLINE RCPT HSG 16POS 制造商:itt cannon, llc 系列:CTC 包装:散装 零件状态:在售 连接器类型:插座 触头类型:公形引脚 针脚数:16 间距:- 排数:4 排距:- 安装类型:自由悬挂 触头端接:压接 紧固类型:锁存器支座 颜色:黑色 特性:密封式 备注:不含触头 标准包装:50 |
发布紧急采购，3分钟左右您将得到回复。