- 您现在的位置：买卖IC网 > Datasheet目录593 > 1338273-1 (TE Connectivity)TOOL DIE ASSY 22-16AWG SOLIS Datasheet资料下载
参数资料
| 型号： | 1338273-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/4页 |
| 文件大小： | 0K |
| 描述： | TOOL DIE ASSY 22-16AWG SOLIS |
| 标准包装： | 1 |
| 系列： | * |
Frequency of inspection depends on:
1. The care, amount of use, and handling of the
dies.
2. The presence of abnormal amounts of dust and
dirt.
3. The degree of operator skill.
4. Your own established standards.
The dies are inspected before being shipped;
however, it is recommended that the dies be
inspected immediately upon arrival at your facility to
ensure that no damage occurred during shipment.
Due to the precision design, it is important that no
parts of these dies be interchanged except those
replacement parts listed in Section 5.
1. Remove dust, moisture, and other contaminants
with a clean brush, or a soft, lint–free cloth. Do
NOT use objects that could damage the dies.
2. When the dies are not in use, store them in a
clean, dry area.
1. Remove accumulated dirt, grease, and foreign
matter by immersing the dies in a suitable
commercial degreaser.
2. Inspect die crimp area for worn, cracked, or
broken surfaces. If damage is evident, refer to
Section 5, REPLACEMENT AND REPAIR, for
information on obtaining customer repair service.
This inspection requires the use of a plug gage
conforming to the dimensions shown in Figure 4. To
gage the crimping chamber, refer to Figure 4, and
proceed as follows:
1. Remove traces of oil or dirt from the crimping
chamber and plug gage.
2. Align the GO element with the crimping
chamber. Push element straight into the chamber
without using force. The GO element must pass
completely through the crimping chamber.
3. Check the crimping chamber with the NO–GO
element in the same manner as Step 2. The
NO–GO element may start entry, but must not
pass completely through the crimping chamber.
If dies conform to the gage inspection, they are
considered dimensionally correct. If not correct, refer
to Section 5, REPLACEMENT AND REPAIR, for
information on obtaining customer repair service.
For additional information regarding the use of a plug
gage, refer to instruction sheet 408–7424.
Figure 4
相关PDF资料 |
PDF描述 |
|---|---|
| 1366402-1 | TOOL HAND 18-22AWG STR ACTION |
| 1366865-1 | EXT-TOOL FOR 025 TAB CONTACT |
| 1372039-1 | TOOL HAND MONO SHAPE MK II |
| 1374484-1 | POLISH FILM 9MM DIAMOND 5" DISK |
| 1375308-4 | PREM IMPACT TL/W BLADE 110/66 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 1338278-1 | 功能描述:ANVIL,12-10 PIDG 制造商:te connectivity amp connectors 系列:* 零件状态:在售 标准包装:1 |
| 1338279-1 | 制造商:TE Connectivity 功能描述:INDENTER,12-10 PIDG - Bulk 制造商:TE CONNECTIVITY 功能描述:INDENTER,12-10 PIDG |
| 1338281-1 | 制造商:TE Connectivity 功能描述:RAM, SPECIAL END FEED - Bulk |
| 1338281-2 | 功能描述:手工工具 RAM, SPECIAL E/FEED RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 1338281-3 | 功能描述:手工工具 RAM, SPECIAL E/FEED RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
发布紧急采购，3分钟左右您将得到回复。