- 您现在的位置：买卖IC网 > PDF目录18488 > 1583093-1 (TE Connectivity)DIE ASSEMBLY AMPOWER #4 PDF资料下载
参数资料
| 型号： | 1583093-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 4/6页 |
| 文件大小： | 0K |
| 描述： | DIE ASSEMBLY AMPOWER #4 |
| 标准包装： | 1 |
| 系列： | * |
| 配用： | 328160-ND - CONN TERMINAL 4AWG STRAIGHT 328178-ND - CONN TERMINAL STR 4AWG #1/2 328164-ND - CONN TERMINAL STR 4AWG #3/8 328163-ND - CONN 4 AWG #5/16 AMPOWER |
| 相关产品： | 1976230-1-ND - HYDRAULIC CRIMPING HEAD ASS Y 1490746-1-ND - TOOL 14 TON CRIMPING HEAD 1490749-1-ND - CRIMP TOOL HYDRAULIC |
408- 8703
5. CRIMP INSPECTION
Inspect crimped terminals and splices by checking the
features described in Figure 5. Use only terminals
and splices that meet the conditions shown in the
“ACCEPT” column of Figure 5. Unacceptable
ACCEPT
terminals and splices, as depicted in the “REJECT”
column of Figure 5 can be avoided through careful
use of the instructions in Section 4 and by performing
regularly scheduled die maintenance as described in
Section 6.
REJECT
Terminal
Parallel
Splice
Butt
Splice
1
Crimped off end of splice or terminal wire barrel.
1
2
3
4
5
Crimps centered. Crimps may be off center BUT NOT OFF
END OF WIRE BARREL.
Embossed wire size matches CMA of wire being used
and wire size stamped on terminal or splice.
Insulation does not enter wire barrel.
Wire is visible through sight hole of terminal or butt splice.
On parallel splices, bare wire ends must be flush with
or extended slightly beyond end of barrel.
2
3
4
5
6
Embossed wire size does not match CMA of wire being
used, or wire size stamped on terminal or splice.
Wire not inserted far enough in terminal or splice. End of
wire must be visible through sight holes of terminals or
butt splices.
Wire insulation entered barrel of terminal or splice. CHECK
FOR INCORRECT STRIP LENGTH.
Excessive “flash” indicates wrong wire, splice, or tooling
combination was used.
Nicked or missing strands.
Figure 5
4 of 6
Rev B
相关PDF资料 |
PDF描述 |
|---|---|
| 9HT10-32.768KAZF-T | CRYSTAL 32.768 KHZ 12.5 PF SMD |
| ABM3-24.576MHZ-D2Y-T | CRYSTAL 24.576 MHZ 18PF SMD |
| 3852C-282-101AL | POT 100 OHM 3/4" RD CERM |
| 91A1A-H28-B15L | POT 10K OHM 5/8" SQ 1/2W PLAS |
| B32520C1104K289 | FILM CAP 0.1000UF 10% 100V |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 1583094-1 | 功能描述:冲压机与冲模 DIE ASSEMBLY AMPOWER #2 RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 1583095-1 | 功能描述:冲压机与冲模 DIE ASSY AMPOWER 1/0 RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 1583096-1 | 功能描述:冲压机与冲模 DIE ASSY AMPOWER 2/0 RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 1583097-1 | 功能描述:冲压机与冲模 DIE ASSY AMPOWER 3/0 RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 1583098-1 | 功能描述:冲压机与冲模 DIE ASSY AMPOWER 4/0 RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
发布紧急采购，3分钟左右您将得到回复。