- 您现在的位置：买卖IC网 > PDF目录18502 > 1583096-1 (TE Connectivity)DIE ASSEMBLY AMPOWER 2/0 PDF资料下载
参数资料
| 型号： | 1583096-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/6页 |
| 文件大小： | 0K |
| 描述： | DIE ASSEMBLY AMPOWER 2/0 |
| 标准包装： | 1 |
| 系列： | * |
| 配用： | 184259-1-ND - CONN AMPOWER TERM 2/0AWG 90DEG 325406-ND - TERM 2/0AWG #0 AMPOWER 53681-2-ND - TERMINAL AMPOWER 2/0AWG TIN 52595-1-ND - CONN TERM QUICK DISC 2/0 AWG 324444-ND - CONN SPLICE PARALLEL 2/0AWG 326801-ND - CONN 2/0 AWG #3/8 AMPOWER 325405-ND - CONN 2/0 AWG #1/2 AMPOWER 325403-ND - CONN 2/0 AWG #3/8 AMPOWER 325401-ND - CONN 2/0 AWG #1/4 AMPOWER 324459-ND - CONN SPLICE BUTT 2/0AWG AMPOWER |
| 相关产品： | 1976230-1-ND - HYDRAULIC CRIMPING HEAD ASS Y 1490746-1-ND - TOOL 14 TON CRIMPING HEAD 1490749-1-ND - CRIMP TOOL HYDRAULIC |
408- 8703
3.2. Die Removal
Ensure that the possibility of accidental activation of
the hydraulic power unit has been eliminated, and
proceed as follows:
1. Depress the upper release button located in the
C--head and slide the nest out of the head.
2. Activate the power unit until the lower die
release button in the ram is exposed.
3. Depress the release button and slide the
indenter out of the ream.
4.2. Crimping Procedure
1. Ensure that the wire size stamped on the
terminal or splice corresponds to the wire size
stamped on the stationary die.
2. Center the terminal or splice in the stationary die
as shown in Figure 4.
3. Activate the power unit so that the moving die
advances and holds the terminal or splice in place
without deforming the wire barrel.
4. Insert the stripped wire until it bottoms in the
terminal or butt splice. The end of the wire must be
visible through the sight hole.
4. WIRE PREPARATION AND CRIMPING PROCEDURES
NOTE
i
Sight holes of butt splices must always face
either the upper or lower die.
4.1. Wire Preparation
1. Select proper size terminal or splice for wire size
being used.
2. Determine correct terminal or splice wire loading
by referring to CMA (Circular Mill Area) range listed
in the table in Figure 1. The total CMA of wires
being used must be within the CMA range of the
terminal or splice.
3. Strip the wire to the dimensions indicated in the
table in Figure 2, taking care not to nick or cut the
wire strands.
5. When inserting the stripped wires into a parallel
splice, the ends of the wires must be at least flush
with, or extend slightly beyond the end of the wire
barrel.
6. Activate the power unit to complete the crimp.
7. To crimp the other half of the butt splice, remove
and reposition the uncrimped half in the stationary
die. Insert the wire until it bottoms against the
splice sire stop (visible through the sight holes),
and then crimp the splice.
8. Inspect the crimp by referring to Section 5,
CRIMP INSPECTION, and to Figure 5.
End of Inserted Wire
Must Be Visible
Through Sight Hole
Terminal
Center Terminal Wire
Barrel in Stationary Die
Ends of Inserted Wires
Must be Visible
Through Sight Holes
Butt Splice
Center Half of Butt Splice in
Stationary Die (Sight Holes
Must Face Upper or Lower Die)
Parallel Splice
Center Parallel Splice
in Stationary Die
Figure 4
Rev B
3 of 6
相关PDF资料 |
PDF描述 |
|---|---|
| B32529C6183J289 | FILM CAP 0.0180UF 5% 400V |
| ABMM2-11.0592MHZ-E2-T | CRYSTAL 11.0592 MHZ 18PF SMD |
| TLF14CBH1021R5K1 | CHOKE COMMON MODE 1000UH |
| SRF0905-251Y | INDUCTOR COMMON MODE 250UH 1.2A |
| TLF14CB3321R0K1 | CHOKE COMMON MODE 3300UH |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 1583097-1 | 功能描述:冲压机与冲模 DIE ASSY AMPOWER 3/0 RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 1583098-1 | 功能描述:冲压机与冲模 DIE ASSY AMPOWER 4/0 RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 15831 | 制造商:3M Electronic Products Division 功能描述: |
| 1583-1 | 功能描述:电路板硬件 - PCB .051 Dbl end turret RoHS:否 制造商:Harwin 类型:Shield Clip 长度:9.4 mm 螺纹大小: 外径: 材料:Beryllium Copper 电镀:Tin |
| 1583100 | 制造商:Phoenix Contact 功能描述:CHRG CBL ELECT VEH MODE 2, 1 PH 制造商:Phoenix Contact 功能描述:Terminal Block Tools & Accessories EV-T1L2C-1AC30A-4 0M10ASBK00 制造商:Phoenix Contact 功能描述:EV-T1L2C-1AC30A-4 0M10ASBK00 |
发布紧急采购，3分钟左右您将得到回复。