- 您现在的位置：买卖IC网 > PDF目录18708 > 1583514-1 (TE Connectivity)TOOLING UPPER MTA 050 PDF资料下载
参数资料
| 型号： | 1583514-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 4/4页 |
| 文件大小： | 0K |
| 描述： | TOOLING UPPER MTA 050 |
| 标准包装： | 1 |
| 系列： | * |
408- 8812
i
i
1. Depress the ribbon cable locating plate mounted
on the connector locator, and install connector as
shown in Figure 6.
NOTE The polarization legs of connector must engage
with connector locator. The connector locator
should engage with connector and return to a
vertical position.
Ensure that connector is loaded correctly before
proceeding.
CAUTION If the connector is not loaded correctly, damage
to connector will result.
!
2. With connector properly loaded, raise the ribbon
cable clamp and lay ribbon cable on top of the
connector and hold in place.
3. Close and latch the ribbon cable clamp.
4. Slide the fixture underneath the upper tooling,
and rotate handle until the upper tooling is fully
seated. Raise the upper tooling, and the slide
fixture to front end stop.
5. Depress the latch and raise the cable clamp.
6. Depress the ribbon cable locating plate and
carefully remove the terminated connector from the
fixture by lifting straight “up.”
CAUTION Do not twist the terminated connector during
unloading, or damage may result.
!
7. PRODUCT INSPECTION
Inspect housing and contacts for physical damage.
Refer to product application specification 114--13072.
8. TOOLING INSPECTION AND MAINTENANCE
8.1. Inspection
It is recommended that the arbor frame assembly be
inspected immediately upon arrival at your facility
(and at regularly scheduled intervals thereafter) to
ensure that it has not been damaged during handling.
8.2. Maintenance and Lubrication
To prolong the useful life of your Arbor Frame
Assembly and MTA--50 Mass Termination Tooling,
and to provide the smoothest operation, maintain and
lubricate monthly as follows:
NOTE Though recommendations call for lubrication at
least once a month, the frequency should be
based on amount of use, working conditions, and
established company policies.
1. Remove the upper tooling and lower tooling.
4 of 4
2. Move the ram to the bottom of its stroke (the
adjustment ring should bottom on the base plate).
Note the position of the handle. Loosen the handle
adjustment knob sufficiently for the handle to slide
from its mounting hole. Remove the handle.
3. Using a small flat--blade screwdriver, turn the
spring plunger counterclockwise until it no longer
contacts the ram.
4. Grip the adjustment ring, and pull it upward,
then remove the ram.
5. Apply ANDEROL 757 ? grease, or equivalent, to
the gear teeth on the ram and to the bore of the
frame.
6. Re--assemble the ram into the bore with the
grooved side of the ram aligned with the spring
plunger. Ensure that the gear teeth in the ram
engage the teeth of the pinion (small diameter gear
in bore of frame) so that the handle position will be
the same as noted in Step 2 when the adjustment
ring bottoms.
7. Turn the spring plunger clockwise until it
bottoms lightly on the ram, then back off one--half
of a turn.
8. Re--assemble the handle and upper tooling and
lower tooling. Ensure proper alignment of tooling
before operating the arbor frame assembly.
9. Remove any excess grease from the outer
surface of the frame and adjustment ring with a
soft cloth.
9. REPLACEMENT AND REPAIR
A complete inventory of customer--replaceable parts
should be stocked and controlled to prevent lost time
when replacement of parts is necessary. Other parts
should be replaced by TE Connectivity to ensure
quality and reliability. Order replacement parts
through your representative, or call 1--800--526--5142,
or send a facsimile of your purchase order to
717--986--7605, or write to:
CUSTOMER SERVICE (038--035)
TYCO ELECTRONICS CORPORATION
PO BOX 3608
HARRISBURG PA 17105--3608
For customer repair service, please contact a
representative at 1--800--526--5136.
10. REVISION SUMMARY
Since the previous version of this document, the
following changes were made:
Updated document to corporate requirements.
Rev A
相关PDF资料 |
PDF描述 |
|---|---|
| GLAA07B | SWITCH TOP PLUNGER SNAP SPDT |
| GLAA01C | SWITCH TOP ROLLR PLNGR SNAP SPDT |
| GLAC01C | SWTCH TOP ROLLR PLUNGR SNAP SPDT |
| DM1810-434-DK | DM1810 433.92 MHZ DEVELOPMENT KI |
| LPR2400ERDKPRO | PRO DEVELOPMENT KIT, SERIAL MODE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 1583517-1 | 制造商:TE CONNECTIVITY 功能描述:FIXTURE ASSY,RIB CABLE MTA 050 |
| 1583518-1 | 功能描述:手工工具 ARBOR PRESS W/SLIDE RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 1583526 | 功能描述:重负荷电源连接器 VC-TFS 6-PE RoHS:否 制造商:Hirose Connector 系列:PS2 产品类型:Connectors 位置/触点数量: 端接类型:Crimp 触点材料: 触点电镀:Gold 电压额定值: 电流额定值:300 A 附件类型: |
| 1583527-1 | 功能描述:手工工具 626 SDE ADAPTER NORM RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 158353027 | 功能描述:LED Lighting WL-SWTC White, Warm 2700K 3.2V 350mA 120° 2-SMD, No Lead, Exposed Pad 制造商:wurth electronics inc 系列:WL-SWTC 包装:剪切带（CT） 零件状态:有效 颜色:暖白色 CCT（K）:2700K 85°C 时通量，电流 - 测试:- 25°C 时通量，电流 - 测试:95 lm（标准） 电流 - 测试:350mA 电压 - 正向（Vf）（典型值）:3.2V 不同测试电流时的流明/瓦:85 lm/W CRI（高显色指数）:80（标准） 电流 - 最大值:1A 视角:120° 安装类型:表面贴装 封装/外壳:2-SMD，无引线，裸露焊盘 封装热阻:8°C/W 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。