参数资料
| 型号： | 16280 |
| 厂商： | Desco |
| 文件页数： | 1/4页 |
| 文件大小： | 0K |
| 描述： | MAT DISS VINYL BEIGE .100 36X40' |
| MSDS 材料安全数据表： | Static Dissipative Type B MSDS |
| 标准包装： | 1 |
| 系列： | STATFREE B™ |
| 垫子类型： | 桌子，工作台卷筒 |
| 形状： | 矩形 |
| 长度： | 40'（12.19m） |
| 宽： | 3'（0.91m） |
| 厚度： | 0.10"（2.54mm） |
| 颜色： | 浅褐 |
| 材质： | 乙烯基 |
| 特点： | 耗散 |
TB-2000 March 2012 Page 1 of 4
Installation and
Maintenance of ESD Mats
Introduction
The purpose of an ESD worksurface is to aid in the prevention
of damage to ESD sensitive components and assemblies from
electrostatic discharge. An ESD worksurface provides protection in
the following two ways:
1. Providing an antistatic worksurface area that will limit static
electricity generation.
2. Removing the charge from a conductive object placed on the
worksurface.
A dissipative worksurface having a surface resistance of at
least 1 x 10E6, but less than 1 x 10E9 ohms is recommended
by worksurface standard ANSI/ESD S4.1. Dissipative materials
minimize the generation of static charges, and will dissipate a
charge slow enough so that a spark will not occur. Dissipative
materials are usually the preferred choice for bench top
worksurfaces.
Conductive materials are the quickest to remove a charge,
but they can also cause damage by discharging too rapidly.
Conductive materials are usually used as floor mats, which is
defined by ANSI/ESD S7.1 as less than 1 x 10E6 ohms.
General Grounding Guidelines
1. ANSI/ESD S20.20 requires that all conductors in an ESD
protected area, including personnel, must be grounded.
2. The ESD ground must be tied directly to and at the same
potential as the building or “green wire” equipment ground.
3. Per ANSI/ESD S20.20, the ESD control program can in no
way replace or supercede any requirements for personnel
safety. Ground fault circuit interrupters (GFCI) and other safety
protection should be considered wherever personnel might
come into contact with electrical sources.
4. All electrical outlets should be verified for proper wiring
configuration, resistance or impedance and GFCI function when
the mat is installed and periodically thereafter.
Common Point Grounds
A common point ground is defined by the grounding standard
ANSI/ESD S6.1, as:
1. A grounded device where two or more conductors are bonded.
2. A system or method for connecting two or more grounding
conductors to the same electrical potential.
Examples of common point grounds with ground cords are
illustrated below.
Figure 2. Other ground cords.
Figure 3. 09814 with screw allows ground cord to be bolted to mat
to keep cord from disconnecting.
Common point grounds are designed to provide ground for
worksurface mats, wrist straps, and other items.
NOTE: DO NOT DAISY CHAIN. Because of the high resistances
inherent to many types of protective surfaces, daisy chaining of
these materials can severely limit their ability to properly dissipate
and protect against static charges.
DESCO WEST
- 3651 Walnut Avenue, Chino, CA 91710 (909) 627-8178
DESCO EAST - One Colgate Way
, Canton, MA 02021-1407 (781) 821-8370 Web Site: Desco.com
TECHNICAL BULLETIN TB-2000
Made in the
United States of America
2012 DESCO INDUSTRIES INC.
Employee Owned
Figure 1. Typical common point grounds.
COMMON POINT GROUND
Per ANSI/ESD S6.1, Grounding section 4.1.1 “Every element to be
grounded at an ESD protected station shall be connected to the
same common point ground.”
ESD Handbook ESD TR20.20 section 5.1.3 Basic Grounding
Requirements “The first step in ensuring that everything in an
EPA is at the same electrical potential is to ground all conductive
components of the work area (worksurfaces, people, equipment,
etc.) to the same electrical ground point. This point is called the
common point ground. The next step in completing the ground
circuit is to connect the common point ground to the equipment
ground (third wire, green).”
WRONG!
RIGHT
Figure 4. ESD mats should never be grounded in series, that is
daisy chained.
相关PDF资料 |
PDF描述 |
|---|---|
| 5-87456-2 | CONN HOUSING 60POS .100 DUAL ROW |
| 0430300008 | CONN TERM FEMALE 20-24AWG 15GOLD |
| 433210-28-0 | TERM BARRIER 28CIRC 1 ROW .4375 |
| G8V-1A7T-R-DC12 | RELAY AUTOMOTIVE SPST 20A 12V |
| 433203-28-0 | TERM BARRIER 28CIRC 1 ROW .4375 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 1628000000 | 功能描述:CONN PCB BLZ 7.50 10POS OR RoHS:是 类别:连接器，互连式 >> 接线座 - 接头，插头和插口 系列:Omnimate BLZ 其它有关文件:ED Part Number Breakdown 产品目录绘图:EDZ1200 Series Front EDZ1200 Series Side 标准包装:50 系列:EDZ1200 端接块类型:插头，母插口 每电平位置:12 间距:0.200"（5.08mm） 级别数目:1 接头定向:- 插头导线入口:180° 端子:螺钉 线规:12-22 AWG 电流:15A 电压:300V 安装类型:自由悬挂 特点:固定锁（非导线侧） 颜色:绿 包装:散装 配套产品:EDSTLZ975/12-SW-ND - TERM BLOCK HDR 5.08MM 12POS PCBEDSTLZ970/12-SW-ND - TERM BLOCK HDR 5.08MM 12POS PCBEDSTLZ975/12-F-ND - TERM BLOCK HDR 5.08MM 12POS PCBEDSTLZ970/12-F-ND - TERM BLOCK HDR 5.08MM 12POS PCBEDSTLZ955/12-OE-ND - TERM BLOCK HDR 5.08MM 12POS PCBEDSTLZ950/12-OE-ND - TERM BLOCK HDR 5.08MM 12POS PCBED1859-ND - TERM BLOCK HDR 5.08MM 12POS PCBED1827-ND - TERM BLOCK HDR 5.08MM 12POS PCBED1917-ND - TERM BLOCK HDR 5.08MM 12POS PCB 其它名称:ED1993 |
| 16280-000-55 | 制造商:Konig & Meyer 功能描述:Support Arms Wall Guitar Mount |
| 16280-1 | 功能描述:栅栏接线端子 POWER DIST. BLOCK RoHS:否 制造商:TE Connectivity / AMP 产品:Barrier Terminal Blocks 系列: 类型:Dual Barrier, Flat Block without Mounting Ears 节距:9.53 mm 位置/触点数量:2 线规量程:22-12 电流额定值:20 A 电压额定值:300 V 安装风格:Through Hole 安装角:Vertical 端接类型:Screw 触点电镀:Tin |
| 1628010000 | 功能描述:CONN PCB BLZ 7.50 11POS OR RoHS:是 类别:连接器，互连式 >> 接线座 - 接头，插头和插口 系列:Omnimate BLZ 其它有关文件:ED Part Number Breakdown 产品目录绘图:EDZ1200 Series Front EDZ1200 Series Side 标准包装:50 系列:EDZ1200 端接块类型:插头，母插口 每电平位置:12 间距:0.200"（5.08mm） 级别数目:1 接头定向:- 插头导线入口:180° 端子:螺钉 线规:12-22 AWG 电流:15A 电压:300V 安装类型:自由悬挂 特点:固定锁（非导线侧） 颜色:绿 包装:散装 配套产品:EDSTLZ975/12-SW-ND - TERM BLOCK HDR 5.08MM 12POS PCBEDSTLZ970/12-SW-ND - TERM BLOCK HDR 5.08MM 12POS PCBEDSTLZ975/12-F-ND - TERM BLOCK HDR 5.08MM 12POS PCBEDSTLZ970/12-F-ND - TERM BLOCK HDR 5.08MM 12POS PCBEDSTLZ955/12-OE-ND - TERM BLOCK HDR 5.08MM 12POS PCBEDSTLZ950/12-OE-ND - TERM BLOCK HDR 5.08MM 12POS PCBED1859-ND - TERM BLOCK HDR 5.08MM 12POS PCBED1827-ND - TERM BLOCK HDR 5.08MM 12POS PCBED1917-ND - TERM BLOCK HDR 5.08MM 12POS PCB 其它名称:ED1993 |
| 162801940TR4 | 制造商:TT Electronics / BI Technologies 功能描述: |
发布紧急采购，3分钟左右您将得到回复。