- 您现在的位置：买卖IC网 > Datasheet目录594 > 1673672-1 (TE Connectivity)CRIMP HEAD SOLIS W/INSR 8-2AWG Datasheet资料下载
参数资料
| 型号： | 1673672-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 4/6页 |
| 文件大小： | 0K |
| 描述： | CRIMP HEAD SOLIS W/INSR 8-2AWG |
| 标准包装： | 1 |
| 系列： | Solistrand |
| 压接或电缆尺寸： | 2-8 AWG |
| 压接手柄： | 59975-1 |
| 连接器类型： | 端子及连接件 |
| 配用： | 8-35187-3-ND - CONN SPLICE PARALLEL UNINS 2AWG 8-34318-3-ND - CONN SPLICE PARALLEL UNINS 8AWG 332042-ND - CONN RING 8AWG #1/4 SOLIS 322445-ND - CONN TAB TONGUE 8AWG SOLIS 320745-ND - CONN RING 6AWG #7/16 SOLIS 322704-ND - CONN RING 4AWG #3/8 SOLIS 8-33468-3-ND - CONN RING 4AWG #10 SOLIS 8-33469-2-ND - CONN RING 4AWG #1/4 SOLIS 8-33462-1-ND - CONN RING 8AWG #5/16 SOLIS 320743-ND - CONN RING 4AWG #7/16 SOLIS 更多... |
| 相关产品： | 1804700-2-ND - PUMP HYDRAULIC HEAVY DUTY 1804700-1-ND - PUMP HYDRAULIC HEAVY DUTY 1583661-1-ND - HAND HYDRAULIC PUMP 1583659-1-ND - FOOT HYDRAULIC PUMP |
Hydraulic Crimping Head 1673672- 1
7. INSPECTION/MAINTENANCE
DANGER Make sure hydraulic pressure is released and
power supply is disconnected before following
inspection and maintenance procedures, unless
otherwise specified in the procedure.
Each crimping head is assembled and inspected
before shipment. It is recommended that the crimping
head be inspected immediately upon its arrival at your
facility, and at regularly scheduled intervals, to ensure
that the crimping head has not been damaged during
handling. Frequency of inspection depends upon the
following: care, amount of use, and handling of the
head; type and size of products crimped; degree of
operator skill; and environmental conditions.
7.1. Cleaning
408- 8910
2. With hydraulic pressure released, inspect the
assembled head for nicks, scratches, and cracks.
Inspect for cracks especially at the corners of the
yoke and around the top of the cylinder.
3. Inspect pivot pin holes and latch pin holes for
wear. Replace parts, as needed.
4. Activate power unit. Raise ram to UP position.
Inspect flat and round surfaces of ram for galling
(fretting or wear by friction), cracks, or oil leakage.
Release pressure and make sure that ram retracts
smoothly.
5. If head shows evidence of galling, cracks, oil
leakage, or rough cycling, return the crimping head
to for repairs. (Refer to Section 8, REPLACEMENT
AND REPAIR).
Remove accumulations of dirt and grease on the
crimping head, especially in areas where dies are
installed and terminals are crimped. Clean the entire
head frequently with a clean, lint--free cloth.
NOTE
i
It is recommended that the head be returned to
Tyco Electronics once a year (or every 7,500
cycles) for magnetic particle inspection. Refer to
Instruction Sheet 408--8909.
i
7.2. Visual Inspection
Refer to Figure 6 and proceed as follows:
1. Visually inspect die closure surfaces for
chipped, pitted, or flattened areas.
Chipped Flattened
Area Area
Pitted
Area
7.3. Die Closure Inspection
Every crimping head die set is inspected for proper
die closure before shipment. However, the dies
should be inspected for excessive wear periodically.
Die closure is accomplished using GO/NO--GO plug
gages. Suggested plug gage design and GO/NO--GO
dimensions are shown in Figure 7.
NOTE Tyco Electronics neither manufactures nor sells
plug gages.
1. Clean the oil and dirt from the closure surfaces,
and plug gage members.
2. Lock the desired nest in the crimp position and
raise the indenter to the full UP position, as shown
in Figure 8, Detail A.
3. With the indenter positioned at the full UP
position, inspect the die closure using the
appropriate plug gage. Hold the gage in alignment
with die closure and carefully insert, without
forcing, the GO member. See Figure 8. The GO
member must pass completely through the die
closure as shown in Figure 8, Detail B.
Check for
Excessive Wear
at all Pivot Points
Figure 6
Check
These
Areas for
Cracks
4. Try to insert the NO--GO member. The NO--GO
member may enter partially, but must NOT pass
completely through the die closure. See Figure 8,
Detail B.
5. If the die closure meets the GO/NO--GO gage
conditions, the die closure is considered
dimensionally correct. If the die closure does not
conform with the GO/NO--GO gage conditions,
contact your local Tyco Electronics Representative.
4 of 6
Tyco Electronics Corporation
Rev B
相关PDF资料 |
PDF描述 |
|---|---|
| 169341-1 | TOOL HAND CRIMP HD-20CONTACTS |
| 169400 | TOOL HAND CRIMP CERTI-LOK |
| 169406 | STABILIZER ASSY |
| 169414-1 | CERTI-LOK LOCATOR |
| 169422-1 | TOOL HAND MINI CERTI-LOK III |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 1673680000 | 功能描述:CONN PLUG 5.08MM 90 15POS SN OR RoHS:是 类别:连接器，互连式 >> 接线座 - 接头，插头和插口 系列:Omnimate SLZF 其它有关文件:ED Part Number Breakdown 产品目录绘图:EDZ1200 Series Front EDZ1200 Series Side 标准包装:50 系列:EDZ1200 端接块类型:插头，母插口 每电平位置:12 间距:0.200"（5.08mm） 级别数目:1 接头定向:- 插头导线入口:180° 端子:螺钉 线规:12-22 AWG 电流:15A 电压:300V 安装类型:自由悬挂 特点:固定锁（非导线侧） 颜色:绿 包装:散装 配套产品:EDSTLZ975/12-SW-ND - TERM BLOCK HDR 5.08MM 12POS PCBEDSTLZ970/12-SW-ND - TERM BLOCK HDR 5.08MM 12POS PCBEDSTLZ975/12-F-ND - TERM BLOCK HDR 5.08MM 12POS PCBEDSTLZ970/12-F-ND - TERM BLOCK HDR 5.08MM 12POS PCBEDSTLZ955/12-OE-ND - TERM BLOCK HDR 5.08MM 12POS PCBEDSTLZ950/12-OE-ND - TERM BLOCK HDR 5.08MM 12POS PCBED1859-ND - TERM BLOCK HDR 5.08MM 12POS PCBED1827-ND - TERM BLOCK HDR 5.08MM 12POS PCBED1917-ND - TERM BLOCK HDR 5.08MM 12POS PCB 其它名称:ED1993 |
| 1673683-1 | 功能描述:手工工具 BLADE,TRIM RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 167-369 | 制造商:Mitutoyo Corporation 功能描述:MICROMETER STANDARD, 1125MM |
| 1673690000 | 功能描述:CONN PLUG 5.08MM 90 16POS SN OR RoHS:是 类别:连接器，互连式 >> 接线座 - 接头，插头和插口 系列:Omnimate SLZF 其它有关文件:ED Part Number Breakdown 产品目录绘图:EDZ1200 Series Front EDZ1200 Series Side 标准包装:50 系列:EDZ1200 端接块类型:插头，母插口 每电平位置:12 间距:0.200"（5.08mm） 级别数目:1 接头定向:- 插头导线入口:180° 端子:螺钉 线规:12-22 AWG 电流:15A 电压:300V 安装类型:自由悬挂 特点:固定锁（非导线侧） 颜色:绿 包装:散装 配套产品:EDSTLZ975/12-SW-ND - TERM BLOCK HDR 5.08MM 12POS PCBEDSTLZ970/12-SW-ND - TERM BLOCK HDR 5.08MM 12POS PCBEDSTLZ975/12-F-ND - TERM BLOCK HDR 5.08MM 12POS PCBEDSTLZ970/12-F-ND - TERM BLOCK HDR 5.08MM 12POS PCBEDSTLZ955/12-OE-ND - TERM BLOCK HDR 5.08MM 12POS PCBEDSTLZ950/12-OE-ND - TERM BLOCK HDR 5.08MM 12POS PCBED1859-ND - TERM BLOCK HDR 5.08MM 12POS PCBED1827-ND - TERM BLOCK HDR 5.08MM 12POS PCBED1917-ND - TERM BLOCK HDR 5.08MM 12POS PCB 其它名称:ED1993 |
| 1673698 | 功能描述:重负荷电源连接器 HC-B 16-SML-67/ O1PG21 RoHS:否 制造商:Hirose Connector 系列:PS2 产品类型:Connectors 位置/触点数量: 端接类型:Crimp 触点材料: 触点电镀:Gold 电压额定值: 电流额定值:300 A 附件类型: |
发布紧急采购，3分钟左右您将得到回复。