参数资料
型号: 17292-2PG-3ES
厂商: Conxall/Switchcraft
文件页数: 35/36页
文件大小: 0K
描述: CONN RCPT 2POS PNL MNT PIN
标准包装: 25
系列: Micro-Con-X®
连接器类型: 插座,公形引脚
位置数: 2
安装类型: 面板安装,隔墙式(前端螺母)
端子: 焊接
紧固型: 插销锁
方向: 带标记
防护等级: 防风雨型
外壳材料,表面处理: 热塑塑胶
触点表面涂层:
包装: 散装
额定电流: 7.5A
电压 - 额定: 600V
工作温度: -40°C ~ 75°C
配套产品: 16282-2SG-315-ND - CONN PLUG 2POS CABLE SKT
16280-2SG-318-ND - CONN PLUG 2POS CABLE SKT
16280-2SG-315-ND - CONN PLUG 2POS CABLE SKT
16280-2SG-311-ND - CONN PLUG 2POS CABLE SKT
16282-2SG-318-ND - CONN PLUG 2POS CABLE SKT
SC1203-ND - CONN PLUG 2POS CABLE SKT
相关产品: 16293SW-ND - GASKET MICRO-CON-X
16291SW-ND - HEX NUT MICRO-CON-X
SC1398-ND - DUST CAP MICRO-CON-X

* Please visit the product pages on our website for the most up-to-date product information
T OOLING
Contact Insertion/Removal Tools
Product not designed to
remove contacts after
insertion. Consult factory
for removal tools.
Manual Contact Crimping Tools
Pneumatic Crimping Tools - Consult Factory
Contact Crimping and Assembly Procedures:
A. Push cable through connector components, i.e. backshell, grommet, sleeve, and coupling ring.
B. Wire preparation: Strip cable to dimensions shown. Make all cuts square and sharp being careful not to nick wires
when cutting. To prevent stranded wires from fraying it is recommended that ends be tightly twisted and not solder
dipped.
Conductor Strip Lengths
CON-X
#20 -3/16
#16 -7/32
#12 -7/32
MIL-E-QUAL
#16 -9/32
#12 -7/32
Cable Stripping
C. Contact crimping tools, use as follows:
Assemble contact locator to tool.
Check tool setting for wire gage to be crimped.
Drop contacts, mating end first into locator so that it rests fully on bottom. Insert stripped lead into contact barrel
until it stops.
Close tool handles completely in one stroke. (The ratchet will not release jaws until tool has completed cycle.)
Inspect crimp to be sure there are no loose strands outside the contact which may short out to an adjacent contact.
D. Contact insertion tools. Place wired contact into proper connectors cavity. Guide tip of the insertion tool so that it starts
at the contact and slides down against the stop. Apply a steady force perpendicular to the contact until it snaps into
position.
?
601 East Wildwood, Villa Park, Illinois 60181 ? Telephone (630) 834-7504 ? Fax (630) 834-8540 ? www.conxall.com
35
相关PDF资料
PDF描述
17291-2PG-3ES CONN RCPT 2POS PNL MNT PIN
VE-25M-IW-F2 CONVERTER MOD DC/DC 10V 100W
17281-2PG-3ES CONN RCPT 2POS PNL MNT PIN
EXP-0921/10/P CONN RCPT 10POS IP68 W/PINS
UP050SL620J-A-B CAP CER 62PF 50V 5% AXIAL
相关代理商/技术参数
参数描述
17292-2SG-300 功能描述:标准环形连接器 MICRO-CONX , LONG PC 2 SOCKT RoHS:否 制造商:Hirose Connector 系列:EM-W 产品类型:Accessories 位置/触点数量:1 触点类型: 触点电镀: 安装风格:Cable 外壳材质: 端接类型:Clamp 电压额定值:
17292-2SG-3ES 功能描述:标准环形连接器 MICRO-CON, LONG PC EPOXY, 2 SOCKT RoHS:否 制造商:Hirose Connector 系列:EM-W 产品类型:Accessories 位置/触点数量:1 触点类型: 触点电镀: 安装风格:Cable 外壳材质: 端接类型:Clamp 电压额定值:
1729230000 功能描述:CONN PCB HDR 3.5MM 30POS SN OR RoHS:是 类别:连接器,互连式 >> 接线座 - 接头,插头和插口 系列:Minimate S2L 其它有关文件:ED Part Number Breakdown 产品目录绘图:EDZ1200 Series Front EDZ1200 Series Side 标准包装:50 系列:EDZ1200 端接块类型:插头,母插口 每电平位置:12 间距:0.200"(5.08mm) 级别数目:1 接头定向:- 插头导线入口:180° 端子:螺钉 线规:12-22 AWG 电流:15A 电压:300V 安装类型:自由悬挂 特点:固定锁(非导线侧) 颜色:绿 包装:散装 配套产品:EDSTLZ975/12-SW-ND - TERM BLOCK HDR 5.08MM 12POS PCBEDSTLZ970/12-SW-ND - TERM BLOCK HDR 5.08MM 12POS PCBEDSTLZ975/12-F-ND - TERM BLOCK HDR 5.08MM 12POS PCBEDSTLZ970/12-F-ND - TERM BLOCK HDR 5.08MM 12POS PCBEDSTLZ955/12-OE-ND - TERM BLOCK HDR 5.08MM 12POS PCBEDSTLZ950/12-OE-ND - TERM BLOCK HDR 5.08MM 12POS PCBED1859-ND - TERM BLOCK HDR 5.08MM 12POS PCBED1827-ND - TERM BLOCK HDR 5.08MM 12POS PCBED1917-ND - TERM BLOCK HDR 5.08MM 12POS PCB 其它名称:ED1993
17292-3PG-300 功能描述:标准环形连接器 MICRO-CON PANEL #20 PC RoHS:否 制造商:Hirose Connector 系列:EM-W 产品类型:Accessories 位置/触点数量:1 触点类型: 触点电镀: 安装风格:Cable 外壳材质: 端接类型:Clamp 电压额定值:
17292-3PG-3ES 功能描述:标准环形连接器 MICRO-CON PANEL #20 PC RoHS:否 制造商:Hirose Connector 系列:EM-W 产品类型:Accessories 位置/触点数量:1 触点类型: 触点电镀: 安装风格:Cable 外壳材质: 端接类型:Clamp 电压额定值: