- 您现在的位置：买卖IC网 > Datasheet目录595 > 180-701-170-000 (Norcomp Inc.)TOOL HIGH DENSITY CRIMP Datasheet资料下载
参数资料
| 型号： | 180-701-170-000 |
| 厂商： | Norcomp Inc. |
| 文件页数： | 2/3页 |
| 文件大小： | 0K |
| 描述： | TOOL HIGH DENSITY CRIMP |
| 标准包装： | 1 |
| 系列： | 180 |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | D-Sub 触点，24-28 AWG |
| 特点： | 侧面插入，棘齿 |
| 产品目录页面： | 281 (CN2011-ZH PDF) |
| 配用： | 85SECT-ND - CONN CONTACT FEMALE 24-26AWG HD 85PECT-ND - CONN CONTACT MALE 24-26AWG HD 85SETR-ND - CONN CONTACT FEMALE 24-26AWG HD 85PETR-ND - CONN CONTACT MALE 24-26AWG HD |
| 其它名称： | 180-701-170-000-ND T3030 |
180-701-170-000
Instruction Sheet
IS-180S
Tool
Stationary
Jaw
5. Holding the wire in place, squeeze the tool
handles together until ratchet releases.
Allow tool handles to open and remove
crimped contact.
Wire Strip
Length
4. CRIMP PULL TEST
Wire & Insulation
should be visible in
Inspection Window
1. Refer to Section 3, CRIMPING
PROCEDURE, and crimp the contact
accordingly to achieve pull test in Figure 3.
Figure 2
3. CRIMPING PROCEDURE
Strip the wire to the length indicated, taking care not
to nick or cut the wire strands. Select an applicable
contact and identify the appropriate crimping
chamber according to the wire size (24-28) markings
on the tool.
WIRE SIZE
Max AWG
28
26
24
Figure 3
TEST PULL
lb.
4
6
8
Refer to Figure 2, and proceed as follows:
1. Hold the tool so that the front is facing you.
Squeeze tool handles together and allow
them to open fully.
2. Insert the contact (mating end first) into the
hole in the locator which corresponds with
the appropriate crimping chamber. Make
sure that the open “U” of the wire barrel and
insulation barrel face the stationary jaw.
5. CRIMP ADJUSTMENT
1. See Manufacturers data sheet (GMT-DS)
supplied with hand tool.
6. DAILY MAINTENANCE
Properly crimped terminals are controlled by the
following maintenance and inspection
procedures.
CAUTION
Make sure that both sides of the
contact insulation barrel are started
evenly into the crimping chamber.
Do NOT attempt to crimp an
improperly positioned contact.
1. Clean all dust, dirt, moisture and other
foreign matter from the crimp jaws that could
damage the crimp area of the dies.
DO NOT immerse tool in cleaning solution
2. The pivot pin and ratcheted pawl-bearing
3. Hold the contact in position, and squeeze
the tool handles together until ratchet
engages sufficiently to hold the contact in
position. Do NOT deform insulation barrel
or wire barrel.
4. Insert stripped wire into contact insulation
and wire barrels until wire and insulation are
visible in inspection window, as shown in
Figure 2.
surface should be lubricated to ensure a
smooth operation.
DO NOT spray oil into tool to lubricate
3. When storing the tool, close the handles
until the ratchet pawl is about to be released
from the tooth of the ratchet. This will help
prevent the dies from being damaged.
NorComp, Inc.
Charlotte, NC
This document is subject to change
Rev 6 11-19-09
Page 2 of 3
Date Printed 11/24/2009
相关PDF资料 |
PDF描述 |
|---|---|
| 180-901-170-000 | TOOL INSERTION/REMOVAL |
| 1828352-1 | HAND HELD VISUAL FAULT LOCATOR |
| 1828867-3 | CABLE LC 50/125 TEST KIT LC/LC |
| 1828868-3 | CABLE LC 62.5/125 TEST KIT LC/LC |
| 1828869-3 | CABLE LC SM TEST KIT LC/LC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 1807-0-15-00-00-00-04-0 | 功能描述:电路板硬件 - PCB PRESS FIT PIN RECPT RoHS:否 制造商:Harwin 类型:Shield Clip 长度:9.4 mm 螺纹大小: 外径: 材料:Beryllium Copper 电镀:Tin |
| 1807-0-15-01-43-14-04-0 | 制造商:Mill-Max Mfg Corp 功能描述:Contact SKT Press Fit ST Thru-Hole Bulk |
| 1807-0-15-01-43-27-04-0 | 功能描述:电路板硬件 - PCB 200u SN/PB OVER NI 43 CON RoHS:否 制造商:Harwin 类型:Shield Clip 长度:9.4 mm 螺纹大小: 外径: 材料:Beryllium Copper 电镀:Tin |
| 1807-0-15-15-43-14-04-0 | 制造商:Mill-Max Mfg Corp 功能描述:1807-0-15-15-43-14-04-0 |
| 1807-0-15-15-43-27-04-0 | 功能描述:电路板硬件 - PCB 10u AU OVER NI 43 CON RoHS:否 制造商:Harwin 类型:Shield Clip 长度:9.4 mm 螺纹大小: 外径: 材料:Beryllium Copper 电镀:Tin |
发布紧急采购，3分钟左右您将得到回复。