- 您现在的位置：买卖IC网 > PDF目录351508 > 18125C334KAT00J KONDENSATOR 330NF 50V 10ST PDF资料下载
参数资料
| 型号： | 18125C334KAT00J |
| 英文描述： | KONDENSATOR 330NF 50V 10ST |
| 中文描述： | KONDENSATOR 330NF 50V 10ST |
| 文件页数： | 18/46页 |
| 文件大小： | 659K |
| 代理商： | 18125C334KAT00J |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页
24
General Specifications
Mechanical
Specification
No evidence of peeling of end terminal
Measuring Conditions
After soldering devices to circuit board apply 5N
(0.51kg f) for 10 ± 1 seconds, please refer to Figure 1.
Specification
Appearance:
No visual defects
Capacitance
Within specified tolerance
Q, Tan Delta
To meet initial requirement
Insulation Resistance
C0G (NP0), X7R
Initial Value x 0.3
Z5U, Y5V
Initial Value x 0.1
Measuring Conditions
Vibration Frequency
10-2000 Hz
Maximum Acceleration
20G
Swing Width
1.5mm
Test Time
X, Y, Z axis for 2 hours each, total 6 hours of test
END TERMINATION ADHERENCE
RESISTANCE TO VIBRATION
Specification
95% of each termination end should be covered with
fresh solder
Measuring Conditions
Dip device in eutectic solder at 230 ± 5°C for
2 ± .5 seconds
Figure 2. Bend Strength
Figure 1.
Terminal Adhesion
SOLDERABILITY
Specification
Appearance:
No visual defects
Capacitance Variation
C0G (NP0): ± 5% or ± .5pF, whichever is larger
X7R:
≤ ± 12%
Z5U:
≤ ± 30%
Y5V:
≤ ± 30%
Insulation Resistance
C0G (NP0):
≥ Initial Value x 0.3
X7R:
≥ Initial Value x 0.3
Z5U:
≥ Initial Value x 0.1
Y5V:
≥ Initial Value x 0.1
Measuring Conditions
Please refer to Figure 2
Deflection:
2mm
Test Time:
30 seconds
BEND STRENGTH
Specification
Appearance:
No serious defects, <25% leaching of either end
terminal
Capacitance Variation
C0G (NP0): ± 2.5% or ± 2.5pF, whichever is greater
X7R:
≤ ± 7.5%
Z5U:
≤ ± 20%
Y5V:
≤ ± 20%
Q, Tan Delta
To meet initial requirement
Insulation Resistance
To meet initial requirement
Dielectric Strength
No problem observed
Measuring Conditions
Dip device in eutectic solder at 260°C, for 1 minute.
Store at room temperature for 48 hours (24 hours for
C0G (NP0)) before measuring electrical parameters.
Part sizes larger than 3.20mm x 2.49mm are reheated
at 150°C for 30 ±5 seconds before performing test.
RESISTANCE TO SOLDER HEAT
Speed = 1mm/sec
R340mm
Supports
2mm
Deflection
45mm
5N FORCE
DEVICE UNDER TEST
TEST BOARD
相关PDF资料 |
PDF描述 |
|---|---|
| 18125C474KA800J | KONDENSATOR 470NF 50V 10ST |
| 18-13-2: | BUCHSE PCB F 75 OHM |
| 18-19: | BUCHSE EINBAU F 75 OHM FRONT |
| 1821 | |
| 1841-01AL30L | Industrial Control IC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 18125C334KAT1A | 制造商:AVX Corporation 功能描述: |
| 18125C334KAT2A | 功能描述:多层陶瓷电容器MLCC - SMD/SMT 1812 0.33uF 50volts X7R 10% RoHS:否 制造商:American Technical Ceramics (ATC) 电容:10 pF 容差:1 % 电压额定值:250 V 温度系数/代码:C0G (NP0) 外壳代码 - in:0505 外壳代码 - mm:1414 工作温度范围:- 55 C to + 125 C 产品:Low ESR MLCCs 封装:Reel |
| 18125C334KAT2A | 制造商:AVX Corporation 功能描述:CAPACITOR CERAMIC 0.33UF 50V X7R 1812 制造商:AVX Corporation 功能描述:CAPACITOR CERAMIC 0.33UF, 50V, X7R, 10%, 1812 |
| 18125C334KAT2A | 制造商:AVX Corporation 功能描述:CAPACITOR 1812 X7R 50V 330NF 制造商:AVX Corporation 功能描述:CAPACITOR, 1812, X7R, 50V, 330NF |
| 18125C334KAT2A/1K | 制造商:AVX Corporation 功能描述:CAP CER 0.33UF 50V 10% X7R 1812 |
发布紧急采购，3分钟左右您将得到回复。