- 您现在的位置：买卖IC网 > Datasheet目录595 > 1901260-1 (TE Connectivity)TOOL HANDLE CRIMPER - LARGE DIES Datasheet资料下载
参数资料
| 型号： | 1901260-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/3页 |
| 文件大小： | 0K |
| 描述： | TOOL HANDLE CRIMPER - LARGE DIES |
| 标准包装： | 1 |
| 系列： | Certi-Crimp II |
| 工具类型： | 手持压接器 - 无模具 |
| 适用于相关产品： | 因模具套件而异 |
| 特点： | 侧面插入，棘齿 |
Wipe excess oil from the tool, particularly from the
crimping area. Oil transferred from the crimping area
onto certain terminations may affect the electrical
characteristics of an application.
1. Close the tool handles until the ratchet releases
and then allow them to open freely. If they do not
open quickly and fully, the spring is defective and
must be replaced. See Section 6, REPLACEMENT
AND REPAIR.
2. Inspect the head for worn, cracked, or broken
crimping dies. If damage is evident, return the tool
for evaluation and repair. See Section 6,
REPLACEMENT AND REPAIR.
3. Check die alignment and tighten the die holding
screws at least twice daily while tool is in use.
Check the ratchet to ensure that the ratchet does not
release prematurely, allowing the dies to open before
they have fully bottomed. Proceed as follows:
1. Remove traces of oil or dirt from the bottoming
surfaces of the dies.
2. Obtain a 0.025 mm [.001 in.] shim that is
suitable for checking the clearance between the
bottoming surfaces of the dies.
3. Select a terminal or splice and maximum size
wire for the terminal or splice.
4. Position the terminal or splice in the crimping
chamber according to according to the instructions
included with the crimping dies. Holding the wire in
place, squeeze the tool handles together until the
ratchet releases. Hold the tool handles in this
position, maintaining just enough pressure to keep
the dies closed.
5. Check the clearance between the bottoming
surfaces of the dies. If the clearance is 0.025 mm
[.001 in.] or less, the ratchet is satisfactory. If
clearance exceeds 0.025 mm [.001 in.], the ratchet
is out of adjustment and must be repaired. See
Section 6, REPLACEMENT AND REPAIR.
Customer–replaceable parts are listed in Figure 3.
A complete inventory should be stocked and
controlled to prevent lost time when replacement of
parts is necessary. Parts other than those listed
should be replaced by Tyco Electronics to ensure
quality and reliability. Order replacement parts
through your representative, or call 1–800–526–5142,
or send a facsimile of your purchase order to
717–986–7605, or write to:
CUSTOMER SERVICE (038–035)
TYCO ELECTRONICS CORPORATION
PO BOX 3608
HARRISBURG PA 17105–3608
For customer repair service, call 1–800–526–5136.
Initial release of document
Figure 3
相关PDF资料 |
PDF描述 |
|---|---|
| 1918805-1 | CLEANER REEL TWO SLOT 1.25/2.5MM |
| 1918808-1 | CLEANER STICK 1.25MM 250PC |
| 1918809-1 | CLEANER MTP/MPO I.B.C. |
| 1918810-1 | CLEANER CARD FIBER CONNECTOR |
| 19286-0065 | TOOL DIELESS HEAD CRIMPER |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 1901262-1 | 制造商:TE Connectivity 功能描述:ASSY,FAKRA CRIMP DIE, 90 DEG - Bulk |
| 1901262-2 | 功能描述:冲压机与冲模 ASSY,FAKRA CRIMP DIE, 90 DEG RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 1901268-1 | 功能描述:ANVIL, STRAIGHT 制造商:te connectivity amp connectors 系列:* 零件状态:有效 标准包装:1 |
| 1901269-1 | 功能描述:CRIMPER, STRAIGHT 制造商:te connectivity amp connectors 系列:* 零件状态:有效 标准包装:1 |
| 1901272-1 | 功能描述:手工工具 BASE, RECEPTACLE RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
发布紧急采购，3分钟左右您将得到回复。