参数资料
| 型号： | 19250 |
| 厂商： | Desco |
| 文件页数： | 3/6页 |
| 文件大小： | 0K |
| 描述： | TESTER COMBO WS & FG NIST |
| 标准包装： | 1 |
| 类型： | 测试仪，鞋和腕带测试 |
| 使用： | 验证鞋具和腕带接地 |
| 特点： | NIST 可追溯，分别用于鞋具和腕带的测试电路 |
| 电源类型： | 9V 电池或 AC 适配器 |
| 包括： | 电池 |
1. Place the Foot Plate on the floor in front of the Combo Tester.
2. Plug the plate’s ground cord into the jack on the left hand
side of the unit.
NOTE: Steps 1 and 2 are not required with the 19252.
DESCO WEST - 3651 Walnut Avenue, Chino, CA 91710 (909) 627-8178
DESCO EAST - One Colgate Way, Canton, MA 02021-1407 (781) 821-8370 Website: Desco.com
Assembly
1. Remove 3 screws from baseplate.
2. Position pedestal on the baseplate with the Tester mounting
bracket pointing away from the operator. Attach pedestal to
baseplate using the three screws provided. Tighten with hex
wrench provided.
TB-2040 Page 3 of 6
Figure 7. Testing foot grounding devices with 19253
2013 DESCO INDUSTRIES INC.
Employee Owned
Figure 8. The 19252 Free Standing Test Fixture
Figure 9. Attaching pedestal to baseplate
Figure 6. Installing ground cord to “FOOT PLATE” jack
3. Press the rocker switch toward “FOOT PLATE.”
4. Place one foot on the plate. If the floor is conductive, lift the
foot you are not testing off of the floor during this test. Make
sure there is no cord plugged into the “WRIST CORD” jack.
5. Press and hold the test button until the test results are
displayed.
6. Lighting of the green “PASS” LED indicates that the foot
ground assemblies are functioning properly.
7. If either red “FAIL LO” or red “FAIL HI” LEDs light and the
audible indicator sounds, the wearer should check the foot
grounding device immediately.
8. Repeat steps 3-6 with other foot.
Free Standing Test Fixture Assembly and
Operation (Model 19252)
The 19252’s rugged steel pedestal tube is powder coated in a
non-conductive white finish that helps to prevent false readings if
contacted by skin or loose smocks.
3. Open the compartment and attach the snap connector to the
included 9 volt battery. Attach poster to the wall at eye level
in front of the Tester location.
4. Install the Tester on the bracket by aligning keyholes on the
back of tester with mounting studs on bracket. While pushing
up on thumb screw, insert the mounting studs into the
keyholes and slide the tester down. See Figure 10.
5. Install the 4” banana plug connector to “FOOT PLATE” jack
on the side of the unit. Insert ring terminal behind thumb
screw.
6. Twist the thumb screw clockwise to secure the tester to the
bracket. Cover thumb screw with vinyl insulator cap.
WRIST STRAP TESTING
This test verifies that a continuous path between the operator,
wrist strap, and ground cord exists.
1. While wearing the wrist strap, plug the banana plug end of
the cord into the jack on the face of the unit.
2. Press rocker switch toward “WRIST CORD”.
3. Press and hold the test button until the test results are
displayed.
NOTE: DO NOT TOUCH ANY OTHER METAL WHILE
PERFORMING TEST.
Thumb screw
Figure 10. Installing Tester on bracket and securing Tester to
bracket
相关PDF资料 |
PDF描述 |
|---|---|
| 1016-2 | SATCHEL 18-1/2 X 13 X 3" |
| 3M3A5-C-TNG | EM AWARE TNG ESD MON STARTER KIT |
| 3M2A4-C-TNG | EM AWARE TNG ESD MON STARTER KIT |
| 767143105GP | RES ARRAY 1M OHM 7 RES 14-SOIC |
| 999-2 | BOX IDS 13-1/8X8-7/8X1-15/16" |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 1925000000 | 制造商:Weidmuller 功能描述:MCP PLUS PLOTTER -EA - Bulk |
| 19250-0003 | 功能描述:手工工具 CAM FEED (24854-21) RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 19250-0004 | 功能描述:手工工具 GUIDE & HOLD DOWN (M MINI MAC) (24854-25) RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 19250-0009 | 功能描述:手工工具 FRONT RAIL W/SPRING W/SPRING (24855-34) RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 19250-0024 | 制造商:MOLEX 功能描述: |
发布紧急采购，3分钟左右您将得到回复。