- 您现在的位置：买卖IC网 > PDF目录298179 > 1N4764ATA2 100 V, 1 W, SILICON, UNIDIRECTIONAL VOLTAGE REGULATOR DIODE, DO-41 PDF资料下载
参数资料
| 型号： | 1N4764ATA2 |
| 元件分类： | 参考电压二极管 |
| 英文描述： | 100 V, 1 W, SILICON, UNIDIRECTIONAL VOLTAGE REGULATOR DIODE, DO-41 |
| 封装： | HERMETIC SEALED, GLASS, DO-204AL, 2 PIN |
| 文件页数： | 7/7页 |
| 文件大小： | 453K |
| 代理商： | 1N4764ATA2 |
1N4728A through 1N4764A Series
http://www.takcheong.com
7
APPLICATION NOTE
Since the actual voltage available from a given zener
diode is temperature dependent, it is necessary to determine
junction temperature under any set of operating conditions
in order to calculate its value. The following procedure is
recommended:
Lead Temperature, TL, should be determined from:
TL = θLAPD + TA.
θLA is the lead-to-ambient thermal resistance (°C/W) and PD
is the power dissipation. The value for
θLA will vary and
depends on the device mounting method.
θLA is generally 30
to 40
°C/W for the various clips and tie points in common use
and for printed circuit board wiring.
The temperature of the lead can also be measured using a
thermocouple placed on the lead as close as possible to the
tie point. The thermal mass connected to the tie point is
normally large enough so that it will not significantly
respond to heat surges generated in the diode as a result of
pulsed operation once steady-state conditions are achieved.
Using the measured value of TL, the junction temperature
may be determined by:
TJ = TL + TJL.
TJL is the increase in junction temperature above the lead
temperature and may be found as follows:
TJL = θJLPD.
θJL may be determined from Figure 3 for dc power
conditions. For worst-case design, using expected limits of
IZ, limits of PD and the extremes of TJ(TJ) may be
estimated. Changes in voltage, VZ, can then be found from:
V = θVZ TJ.
θVZ, the zener voltage temperature coefficient, is found
from Figure 2.
Under high power-pulse operation, the zener voltage will
vary with time and may also be affected significantly by the
zener resistance. For best regulation, keep current
excursions as low as possible.
Surge limitations are given in Figure 5. They are lower
than would be expected by considering only junction
temperature, as current crowding effects cause temperatures
to be extremely high in small spots, resulting in device
degradation should the limits of Figure 5 be exceeded.
相关PDF资料 |
PDF描述 |
|---|---|
| 1N4895-1 | 6.35 V, SILICON, VOLTAGE REFERENCE DIODE, DO-35 |
| 1N4892-1 | 6.35 V, SILICON, VOLTAGE REFERENCE DIODE, DO-35 |
| 1N4902 | 12.8 VOLT LOW NOISE TEMPERATURE COMPENSATED ZENER REFERENCE DIODES |
| 1N4933GP/71 | 1 A, 50 V, SILICON, SIGNAL DIODE, DO-204AL |
| 1N4933GP/54 | 1 A, 50 V, SILICON, SIGNAL DIODE, DO-204AL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 1N4764A-TAP | 功能描述:稳压二极管 100 Volt 1.3 Watt RoHS:否 制造商:Vishay Semiconductors 齐纳电压:12 V 电压容差:5 % 电压温度系数:0.075 % / K 齐纳电流: 功率耗散:3 W 最大反向漏泄电流:3 uA 最大齐纳阻抗:7 Ohms 最大工作温度:+ 150 C 安装风格:SMD/SMT 封装 / 箱体:DO-214AC 封装:Reel |
| 1N4764A-TR | 功能描述:稳压二极管 100 Volt 1.3 Watt RoHS:否 制造商:Vishay Semiconductors 齐纳电压:12 V 电压容差:5 % 电压温度系数:0.075 % / K 齐纳电流: 功率耗散:3 W 最大反向漏泄电流:3 uA 最大齐纳阻抗:7 Ohms 最大工作温度:+ 150 C 安装风格:SMD/SMT 封装 / 箱体:DO-214AC 封装:Reel |
| 1N4764A-TR/BKN | 制造商:Vishay Semiconductors 功能描述:ZENER-DIODE 1.0W, 5%, DO-41, CUT TAPE |
| 1N4764AUR | 制造商:Aeroflex 功能描述:COMMERCIAL ZENER VOLTAGE REGUL 制造商:Aeroflex / Metelics 功能描述:COMMERCIAL ZENER VOLTAGE REGULATOR DIODE - Bulk 制造商:Microsemi Corporation 功能描述:ZENER SGL 100V 5% 1W 2PIN DO-213AB - Bulk |
| 1N4764CE3/TR13 | 制造商:Microsemi Corporation 功能描述:DIODE ZENER 1.0W 100V 2% DO41 |
发布紧急采购，3分钟左右您将得到回复。