参数资料
型号: 1N5286RL
厂商: MOTOROLA INC
元件分类: 稳流二极管
英文描述: 0.3 mA, SILICON, CURRENT REGULATOR DIODE, DO-204AA
文件页数: 3/5页
文件大小: 119K
代理商: 1N5286RL
1N5283 through 1N5314
Motorola TVS/Zener Device Data
9-4
1.5 Watt DC Power Data Sheet
5
4
3
2
1
0
–20
–40
–60
–80
–100
300
250
200
150
100
50
10
7
5
3
2
1
0.7
0.5
0.3
0.2
0.1
–2
–1
0
20
40
60
80
100
120
140
160
0
0.2
0.4
0.6
0.8
1
0.1
0.2
0.3
0.5
0.7
1
2
3
5
7
10
20
30
50
70
100
REVERSE
FORWARD
ANODE
CATHODE
+
ZK @ VK
VL @ IL
POV
IP & ZT @ VT
VAK, ANODE-CATHODE VOLTAGE (VOLTS)
REVERSE
FOR
W
ARD
I D
,DIODE
CURRENT
(mA)
L, LEAD LENGTH (INCHES)
JL
,JUNCTION-T
O-LEAD
THERMAL
RESIST
ANCE
(
C/W)°
θ
POINT OF LEAD TEMPERATURE
MEASUREMENT
(MOST HEAT CONDUCTION IS
THROUGH THE CATHODE LEAD)
L
1N5313
1N5309
1N5305
1N5298
1N5290
TJ = 25°C
POV = 100 V
(DATA OBTAINED
FROM PULSE TESTS)
VAK, ANODE-CATHODE VOLTAGE (VOLTS)
I D
,FOR
W
ARD
DIODE
CURRENT
(mA)
Diode Current.
Limiting Current: 80% of IP minimum used to determine
Limiting voltage, VL.
Pinch-off Current: Regulator current at specified Test
Voltage, VT.
Peak Operating Voltage: Maximum voltage to be applied
to device.
Current Temperature Coefficient.
Anode-to-cathode Voltage.
Knee Impedance Test Voltage: Specified voltage used to
establish Knee Impedance, ZK.
Limiting Voltage: Measured at IL, VL, together with Knee
AC Impedance, ZK, indicates the Knee characteristics of
the device.
Test Voltage: Voltage at which IP and ZT are specified.
Knee AC Impedance at Test Voltage: To test for ZK, a 90
Hz signal VK with RMS value equal to 10% of test voltage,
VK, is superimposed on VK:
ZK = VK/iK
where iK is the resultant ac current due to VK.
To provide the most constant current from the diode, ZK
should be as high as possible; therefore, a minimum value
of ZK is specified.
AC Impedance at Test Voltage: Specified as a minimum
value. To test for ZT, a 90 Hz signal with RMS value equal
to 10% of Test Voltage VT, is superimposed on VT.
SYMBOLS AND DEFINITIONS
APPLICATION NOTE
As the current available from the diode is temperature dependent,
it is necessary to determine junction temperature, TJ, under specific
operating conditions to calculate the value of the diode current. The
following procedure is recommended:
Lead Temperature, TL, shall be determined from:
TL = θLA PD + TA
where
θLA is lead-to-ambient thermal resistance
and
PD is power dissipation.
θLA is generally 30–40°C/W for the various clips and tie points
in common use, and for printed circuit-board wiring.
Junction Temperature, TJ, shall be calculated from:
TJ = TL + θJL PD
where
θJL is taken from Figure 2.
For circuit design limits of VAK, limits of PD may be estimated and
extremes of TJ may be computed. Using the information on Figures
4 and 5, changes in current may be found. To improve current
regulation, keep VAK low to reduce PD and keep the leads short,
especially the cathode lead, to reduce
θJL.
Figure 1. Typical Current Regulator
Characteristics
Figure 2. Typical Thermal Resistance
Figure 3. Typical Forward Characteristics
ID —
IL —
IP —
POV —
θl —
VAK —
VK —
VL —
VT —
ZK —
ZT —
相关PDF资料
PDF描述
1N5289RL 0.43 mA, SILICON, CURRENT REGULATOR DIODE, DO-204AA
1N5294RL 0.75 mA, SILICON, CURRENT REGULATOR DIODE, DO-204AA
1N5298RL 1.1 mA, SILICON, CURRENT REGULATOR DIODE, DO-204AA
1N5308RL 2.7 mA, SILICON, CURRENT REGULATOR DIODE, DO-204AA
1N5309RL 3 mA, SILICON, CURRENT REGULATOR DIODE, DO-204AA
相关代理商/技术参数
参数描述
1N5286UR-1 制造商:Microsemi Corporation 功能描述:Diode Current Reg. 100V 0.33mA 2-Pin DO-213AB 制造商:Microsemi Corporation 功能描述:CURRENT LIMITER DIODE DO-213AB LAW - Bulk
1N5287 功能描述:稳流二极管 .33mA Curr Reg RoHS:否 制造商:Central Semiconductor 最大调节器电流:5.17 mA 最大极限电压:2.9 V 最大峰值工作电压:100 V 安装风格:Through Hole 封装 / 箱体:DO-204AH 封装:
1N5287-1 制造商:Microsemi Corporation 功能描述:CURRENT LIMITER DIODE DO-7 LAW - Bulk
1N5287-1JAN 制造商:Aeroflex 功能描述:JAN1N5287-1
1N5287-1JANTX 制造商:Aeroflex 功能描述:JANTX1N5287-1