参数资料
| 型号： | 1N6373RL4 |
| 厂商： | ON Semiconductor |
| 文件页数： | 4/6页 |
| 文件大小： | 0K |
| 描述： | TVS ZENER UNIDIR 1500W 6V AXIAL |
| 产品变化通告： | Product Discontinuation 20/Aug/2008 |
| 标准包装： | 10 |
| 系列： | Mosorb™ |
| 电压 - 反向隔离（标准值）： | 5V |
| 电压 - 击穿： | 6V |
| 功率（瓦特）： | 1500W |
| 电极标记： | 单向 |
| 安装类型： | 通孔 |
| 封装/外壳： | DO-201AD，轴向 |
| 供应商设备封装： | 轴向 |
| 包装： | 剪切带 (CT) |
| 其它名称： | 1N6373RL4OSCT |
1N6373 - 1N6381 Series (ICTE-5 - ICTE-36)
21.2 V
1000
500
200
100
50
20
10
5
T L = 25 ° C
t P = 10 m s
V BR(MIN) = 6.0 to 11.7 V
19 V
42.4 V
1
0.7
0.5
0.3
0.2
0.1
0.07
0.05
0.03
PULSE WIDTH
10 ms
1 ms
2
1
0.3 0.5 0.7 1 2 3 5 7 10 20 30
D V BR , INSTANTANEOUS INCREASE IN V BR ABOVE V BR(NOM) (VOLTS)
0.02
0.01
0.1
0.2
0.5
1
10 m s
2 5 10
D, DUTY CYCLE (%)
100 m s
20
50 100
Figure 6. Dynamic Impedance
Figure 7. Typical Derating Factor for Duty Cycle
APPLICATION NOTES
RESPONSE TIME
In most applications, the transient suppressor device is
placed in parallel with the equipment or component to be
protected. In this situation, there is a time delay associated
with the capacitance of the device and an overshoot
condition associated with the inductance of the device and
the inductance of the connection method. The capacitance
effect is of minor importance in the parallel protection
scheme because it only produces a time delay in the
transition from the operating voltage to the clamp voltage as
shown in Figure 8.
The inductive effects in the device are due to actual
turn‐on time (time required for the device to go from zero
current to full current) and lead inductance. This inductive
effect produces an overshoot in the voltage across the
equipment or component being protected as shown in
Figure 9. Minimizing this overshoot is very important in the
application, since the main purpose for adding a transient
suppressor is to clamp voltage spikes. These devices have
excellent response time, typically in the picosecond range
and negligible inductance. However, external inductive
circuit layout, minimum lead lengths and placing the
suppressor device as close as possible to the equipment or
components to be protected will minimize this overshoot.
Some input impedance represented by Z in is essential to
prevent overstress of the protection device. This impedance
should be as high as possible, without restricting the circuit
operation.
DUTY CYCLE DERATING
The data of Figure 1 applies for non‐repetitive conditions
and at a lead temperature of 25 ° C. If the duty cycle increases,
the peak power must be reduced as indicated by the curves
of Figure 7. Average power must be derated as the lead or
ambient temperature rises above 25 ° C. The average power
derating curve normally given on data sheets may be
normalized and used for this purpose.
At first glance the derating curves of Figure 7 appear to be
in error as the 10 ms pulse has a higher derating factor than
the 10 m s pulse. However, when the derating factor for a
given pulse of Figure 7 is multiplied by the peak power value
of Figure 1 for the same pulse, the results follow the
expected trend.
effects could produce unacceptable overshoot. Proper
http://onsemi.com
4
相关PDF资料 |
PDF描述 |
|---|---|
| 1SMA15CAT3 | TVS ZENER BIDIRECT 400W 15V SMA |
| AD8606ACBZ-REEL7 | IC OPAMP GP R-R CMOS DUAL 8WLCSP |
| RP1608S-120-F | RES HP 12 OHM 1/5W 1% 0603 SMD |
| 1SMB15AT3 | TVS ZENER UNIDIRECT 600W 15V SMB |
| AD8628WAUJZ-R7 | IC OPAMP CHOPPER R-R 5TSOT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 1N6373RL4G | 功能描述:TVS 二极管 - 瞬态电压抑制器 6.3V 1500W Unidirectional RoHS:否 制造商:Vishay Semiconductors 极性:Bidirectional 工作电压: 击穿电压:58.9 V 钳位电压:77.4 V 峰值浪涌电流:38.8 A 系列: 封装 / 箱体:DO-214AB 最小工作温度:- 55 C 最大工作温度:+ 150 C |
| 1N6373RL4G-CUT TAPE | 制造商:ON 功能描述:1N6373 Series 6 V 1500 W Unidirectional Zener Transient Voltage Suppressor |
| 1N6373TR | 制造商:Micro Commercial Components (MCC) 功能描述:DIODE |
| 1N6374 | 功能描述:TVS 二极管 - 瞬态电压抑制器 9.4V 1500W RoHS:否 制造商:Vishay Semiconductors 极性:Bidirectional 工作电压: 击穿电压:58.9 V 钳位电压:77.4 V 峰值浪涌电流:38.8 A 系列: 封装 / 箱体:DO-214AB 最小工作温度:- 55 C 最大工作温度:+ 150 C |
| 1N6374/1 | 功能描述:TVS 二极管 - 瞬态电压抑制器 1500W 8.0V 10% Uni RoHS:否 制造商:Vishay Semiconductors 极性:Bidirectional 工作电压: 击穿电压:58.9 V 钳位电压:77.4 V 峰值浪涌电流:38.8 A 系列: 封装 / 箱体:DO-214AB 最小工作温度:- 55 C 最大工作温度:+ 150 C |
发布紧急采购，3分钟左右您将得到回复。