- 您现在的位置：买卖IC网 > PDF目录18639 > 2-5435668-8 (TE Connectivity)SWITCH DIP 8POS LOWPRO SEAL GOLD PDF资料下载
参数资料
| 型号： | 2-5435668-8 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/4页 |
| 文件大小： | 0K |
| 描述： | SWITCH DIP 8POS LOWPRO SEAL GOLD |
| RoHS指令信息： | 2-5435668-8 Statement of Compliance |
| 产品目录绘图： | 7100 Series_8 |
| 特色产品： | TE Connectivity Switches |
| 3D 型号： | 2-5435668-8.pdf |
| 标准包装： | 14 |
| 系列： | 7100 |
| 电路： | 单刀单掷 |
| 位置数： | 8 |
| 触点额定电压： | 0.06A @ 5VDC |
| 触动器类型： | 摇臂 |
| 触动器电平： | 凹槽式 |
| 安装类型： | 通孔 |
| 方向： | 顶部触动 |
| 可清洗： | 是 |
| 产品目录页面： | 2570 (CN2011-ZH PDF) |
| 其它名称： | 450-1399 |
408- 7779
Protective Cover
Grip Here
Housing Bottomed
on PC Board
PC Board
Clinched Contact Lead (Inward Only)
Cover Latch
Figure 5
Figure 3
NOTE
For pc board soldering and cleaning procedures,
and recommended solvents, refer to Application
Specification 114--1056.
Low-- Profile Switch
3.2. PC Board Installation
1. Make a layout on the pc board according to the
dimensions shown in Figure 4.
2. Make certain all contact leads have started entry
into holes. Grip sides of switch and push switch
into pc board until it is bottomed.
3. Hold switch at a slight angle and start one row
on contact leads into pc board holes. Do NOT
over--insert. Switch should be rotated until second
row of contact leads are aligned with opposite row
of contact holes.
4. SWITCH PROGRAMMING
After the switch has been inserted into the DIP socket
or soldered onto the pc board, proceed as follows:
1. Remove seal from the switches, see Figure 6.
Remove Tape
Seal from
End
Use Light Pressure
to Insert Switch
Rotate to Align Second
Row - Then Push Down
on Ends of Switch
7.62 [.300] Ref
2.54 [.100] Ref
NOTE: These same procedures
apply to socket installation.
Remove Seal from Top
Left to Bottom Right
(Diagonal Across the
Switch)
Masking Material
Seal
Figure 4
Standard-- Profile or
Side-- Actuated Switch
NOTE
Rev B
To hold switch in place during wave soldering, the
four outside contact leads may be clinched
inward at 45 ? . Refer to Figure 5.
Figure 6
3 of 4
相关PDF资料 |
PDF描述 |
|---|---|
| MCEEZW-H1-0000-0000H027F | XLAMP MCE EASYWHITE LED SERIES |
| 553S3S72 | CBL STR FMALE-R/A FMALE 3POS 6' |
| MTGEZW-00-0000-0B0UC030F | XLAMP MTG SERIES LED WHITE |
| MTGEZW-00-0000-0B0UB027F | XLAMP MTG SERIES LED WHITE |
| MTGEZW-00-0000-0B0PD030F | XLAMP MTG SERIES LED WHITE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 2-5435668-9 | 功能描述:DIP 开关/ SIP 开关 DIP SW 9 POSN W/TAPE AU RoHS:否 制造商:Omron Electronics 位置数量:10 开关类型:DIP 执行器:Rotary 端子节距:2.54 mm 触点形式: 端接类型:Solder Pin 电流额定值:100 mA 电压额定值 DC: 工作温度范围: 安装:Through Hole |
| 2-5435802-0 | 功能描述:DIP 开关/ SIP 开关 10 POS SIDE ACT SLD RoHS:否 制造商:Omron Electronics 位置数量:10 开关类型:DIP 执行器:Rotary 端子节距:2.54 mm 触点形式: 端接类型:Solder Pin 电流额定值:100 mA 电压额定值 DC: 工作温度范围: 安装:Through Hole |
| 2-5435802-1 | 功能描述:DIP 开关/ SIP 开关 RIGHT ANGLE DIP SW 11 P SEALED RoHS:否 制造商:Omron Electronics 位置数量:10 开关类型:DIP 执行器:Rotary 端子节距:2.54 mm 触点形式: 端接类型:Solder Pin 电流额定值:100 mA 电压额定值 DC: 工作温度范围: 安装:Through Hole |
| 2-5435802-2 | 功能描述:DIP 开关/ SIP 开关 R/A 12P SEALED DIP SWITCH RoHS:否 制造商:Omron Electronics 位置数量:10 开关类型:DIP 执行器:Rotary 端子节距:2.54 mm 触点形式: 端接类型:Solder Pin 电流额定值:100 mA 电压额定值 DC: 工作温度范围: 安装:Through Hole |
| 2-5435802-9 | 制造商:TE Connectivity 功能描述:SW,RA DIP 4P SEALED W/O # MARK |
发布紧急采购，3分钟左右您将得到回复。