参数资料
| 型号： | 20-101-0405 |
| 厂商： | Rabbit Semiconductor |
| 文件页数： | 68/80页 |
| 文件大小： | 0K |
| 描述： | MODULE RABBITCORE RCM2010 |
| 标准包装： | 1 |
| 系列： | RabbitCore® |
| 模块/板类型： | MPU 核心模块 |
| 适用于相关产品： | RCM2010 |
| 产品目录页面： | 620 (CN2011-ZH PDF) |
| 其它名称： | 316-1084 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页当前第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页
66
RabbitCore RCM2000
C.2 Chip Select Circuit
Figure C-4 shows a schematic of the chip select circuit.
Figure C-4. Chip Select Circuit
The current drain on the battery in a battery-backed circuit must be kept to a minimum.
When the RCM2000 is not powered, the battery keeps the SRAM memory contents and
the real-time clock (RTC) going. The SRAM has a powerdown mode that greatly reduces
power consumption. This powerdown mode is activated by raising the chip select (CS)
signal line. Normally the SRAM requires Vcc to operate. However, only 2 V is required
for data retention in powerdown mode. Thus, when power is removed from the circuit, the
battery voltage needs to be provided to both the SRAM power pin and to the CS signal
line. The CS control circuit accomplishes this task for the CS signal line.
In a powered-up condition, the CS control circuit must allow the processor’s chip select
signal /CS1 to control the SRAM’s CS signal /CSRAM. So, with power applied, /CSRAM
must be the same signal as /CS1, and with power removed, /CSRAM must be held high
(but only needs to be battery voltage high). Q13 and Q14 are MOSFET transistors with
opposing polarity. They are both turned on when power is applied to the circuit. They
allow the CS signal to pass from the processor to the SRAM so that the processor can peri-
odically access the SRAM. When power is removed from the circuit, the transistors will
turn off and isolate /CSRAM from the processor. The isolated /CSRAM line has a 100 k
pullup resistor to VRAM (R28). This pullup resistor keeps /CSRAM at the VRAM voltage
level (which under no-power conditions is the backup battery’s regulated voltage at a little
more than 2 V).
Transistors Q13 and Q14 are of opposite polarity so that a rail-to-rail voltages can be
passed. When the /CS1 voltage is low, Q13 will conduct. When the /CS1 voltage is high,
Q14 will conduct. It takes time for the transistors to turn on, creating a propagation delay.
This delay is typically very small, about 10 ns to 15 ns.
/CS1
/CSRAM
/RES
Q10
Q13
Q14
R15
R28
VRAM
22 kW
C6
R5
100 kW
1 nF
相关PDF资料 |
PDF描述 |
|---|---|
| 20-101-1093 | RCM4110 RABBITCORE |
| 20-101-0453 | MODULE RABBITCORE RCM2300 |
| 20-101-1235 | CORE MODULE RCM5700 |
| 11FMN-BMTTR-A-TB | CONN FMN HSNG 11POS STAG REV SMD |
| 046232103103800+ | CONN FFC/FPC 3POS 1MM R/A SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 20-101-0410 | 功能描述:单板计算机 OP6700/6600 battery RoHS:否 制造商:Ampro By ADLINK 外观尺寸:EPIC 处理器类型:Intel Atom D510 频率:1.66 GHz 存储容量:2 GB (max) 存储类型:DDR2, L2 Cache 接口类型:Ethernet, PS/2, SATA, Serial, USB 工作电源电压:5 V, 12 V 功耗:13 W 最大工作温度:+ 70 C 尺寸:165.1 mm x 114.3 mm |
| 20-101-0411 | 功能描述:单板计算机 OP6700 RoHS:否 制造商:Ampro By ADLINK 外观尺寸:EPIC 处理器类型:Intel Atom D510 频率:1.66 GHz 存储容量:2 GB (max) 存储类型:DDR2, L2 Cache 接口类型:Ethernet, PS/2, SATA, Serial, USB 工作电源电压:5 V, 12 V 功耗:13 W 最大工作温度:+ 70 C 尺寸:165.1 mm x 114.3 mm |
| 20-101-0412 | 功能描述:单板计算机 OP6600 RoHS:否 制造商:Ampro By ADLINK 外观尺寸:EPIC 处理器类型:Intel Atom D510 频率:1.66 GHz 存储容量:2 GB (max) 存储类型:DDR2, L2 Cache 接口类型:Ethernet, PS/2, SATA, Serial, USB 工作电源电压:5 V, 12 V 功耗:13 W 最大工作温度:+ 70 C 尺寸:165.1 mm x 114.3 mm |
| 20-101-0420 | 功能描述:模块配件 FWT27/Pluggable RoHS:否 制造商:Lantronix 产品: 用于: |
| 20-101-0421 | 功能描述:模块配件 FWT18/Pluggable RoHS:否 制造商:Lantronix 产品: 用于: |
发布紧急采购，3分钟左右您将得到回复。