收藏本站
参数资料
型号： 20-101-1132
厂商： Rabbit Semiconductor
文件页数： 81/134页
文件大小： 0K
描述： MODULE RCM4210 RABBITCORE
产品培训模块： WiFi Authentication
标准包装： 1
系列： RabbitCore®
模块/板类型： MPU 核心模块
适用于相关产品： RCM4210
其它名称： 316-1125
44
RabbitCore RCM4200
4.5 Other Hardware
4.5.1 Clock Doubler
The RCM4200 takes advantage of the Rabbit 4000 microprocessor’s internal clock doubler.
A built-in clock doubler allows half-frequency crystals to be used to reduce radiated
emissions. The 58.98 MHz frequency specified for the RCM4200 model is generated
using a 29.49 MHz crystal.
The clock doubler may be disabled if 58.98 MHz clock speeds are not required. Disabling
the Rabbit 4000 microprocessor’s internal clock doubler will reduce power consumption
and further reduce radiated emissions. The clock doubler is disabled with a simple config-
uration macro as shown below.
4.5.2 Spectrum Spreader
The Rabbit 4000 features a spectrum spreader, which helps to mitigate EMI problems. The
spectrum spreader is on by default, but it may also be turned off or set to a stronger setting.
The means for doing so is through a simple configuration macro as shown below.
NOTE: Refer to the Rabbit 4000 Microprocessor User’s Manual for more information
on the spectrum-spreading setting and the maximum clock speed.
1. Select the “Defines” tab from the Dynamic C Options > Project Options menu.
2. Add the line CLOCK_DOUBLED=0 to always disable the clock doubler.
The clock doubler is enabled by default, and usually no entry is needed. If you need to
specify that the clock doubler is always enabled, add the line CLOCK_DOUBLED=1 to
always enable the clock doubler.
3. Click OK to save the macro. The clock doubler will now remain off whenever you are
in the project file where you defined the macro.
1. Select the “Defines” tab from the Dynamic C Options > Project Options menu.
2. Normal spreading is the default, and usually no entry is needed. If you need to specify
normal spreading, add the line
ENABLE_SPREADER=1
For strong spreading, add the line
ENABLE_SPREADER=2
To disable the spectrum spreader, add the line
ENABLE_SPREADER=0
NOTE: The strong spectrum-spreading setting is not recommended since it may limit
the maximum clock speed or the maximum baud rate. It is unlikely that the strong set-
ting will be used in a real application.
3. Click OK to save the macro. The spectrum spreader will now remain off whenever you
are in the project file where you defined the macro.
相关PDF资料
PDF描述
20-101-1094 MCU RCM4000 RABBITCORE
345-030-540-802 CONN CARDEDGE 30POS .100 X .200
305-030-500-202 CONN CARDEDGE 30POS .156 X .140
243-002-542-101 MINI CARD EDGE 0.2" - 2PIN 1ROW
20-101-1217 MODULE RABBITCORE RCM3229
相关代理商/技术参数
参数描述
20-101-1136 功能描述:射频模块 RF Module Interface RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm
20-101-1138 功能描述:模块化系统 - SOM RCM4300 RABBITCORE RoHS:否 制造商:Digi International 外观尺寸:ConnectCore 9P 处理器类型:ARM926EJ-S 频率:150 MHz 存储容量:8 MB, 16 MB 存储类型:NOR Flash, SDRAM 接口类型:I2C, SPI, UART 工作电源电压:3.3 V 最大工作温度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
20-101-1139 功能描述:模块化系统 - SOM RCM4310 RABBITCORE RoHS:否 制造商:Digi International 外观尺寸:ConnectCore 9P 处理器类型:ARM926EJ-S 频率:150 MHz 存储容量:8 MB, 16 MB 存储类型:NOR Flash, SDRAM 接口类型:I2C, SPI, UART 工作电源电压:3.3 V 最大工作温度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
20-101-1140 功能描述:WiFi/802.11模块 RCM4400W CORE MODULE Wi-Fi/802.11 RoHS:否 制造商:Taiyo Yuden 支持协议:802.11 b/g/n 频带: 数据速率:150 Mbps 接口类型:SDIO 传输功率（最大）: 天线连接器类型: 工作电源电压:3.4 V to 5.5 V 传输供电电流: 接收供电电流: 最大工作温度:+ 80 C 尺寸:35 mm x 15 mm x 2.9 mm
20-101-1153 功能描述:子卡和OEM板 RCM4300 Proto board RoHS:否 制造商:BeagleBoard by CircuitCo 产品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*