参数资料
| 型号： | 24AA256T/SM |
| 厂商： | Microchip Technology |
| 文件页数： | 12/38页 |
| 文件大小： | 0K |
| 描述： | IC EEPROM 256KBIT 400KHZ 8SOIC |
| 产品培训模块： | I2C Serial EEPROM |
| 标准包装： | 2,100 |
| 格式 - 存储器： | EEPROMs - 串行 |
| 存储器类型： | EEPROM |
| 存储容量： | 256K (32K x 8) |
| 速度： | 100kHz，400kHz |
| 接口： | I²C，2 线串口 |
| 电源电压： | 1.7 V ~ 5.5 V |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 8-SOIC（0.209"，5.30mm 宽） |
| 供应商设备封装： | 8-SOIJ |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页当前第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
24AA256/24LC256/24FC256
8.0
READ OPERATION
8.2
Random Read
Read operations are initiated in much the same way as
write operations, with the exception that the R/W bit of
the control byte is set to ‘ 1 ’. There are three basic types
of read operations: current address read, random read
and sequential read.
Random read operations allow the master to access
any memory location in a random manner. To perform
this type of read operation, the word address must first
be set. This is done by sending the word address to the
24XX256 as part of a write operation (R/W bit set to
‘ 0 ’). Once the word address is sent, the master gener-
8.1
Current Address Read
ates a Start condition following the acknowledge. This
terminates the write operation, but not before the
The 24XX256 contains an address counter that main-
tains the address of the last word accessed, internally
incremented by ‘ 1 ’. Therefore, if the previous read
access was to address ‘n’ (n is any legal address), the
next current address read operation would access data
from address n + 1 .
Upon receipt of the control byte with R/W bit set to ‘ 1 ’,
the 24XX256 issues an acknowledge and transmits the
8-bit data word. The master will not acknowledge the
transfer, but does generate a Stop condition and the
internal Address Pointer is set. The master then issues
the control byte again, but with the R/W bit set to a one.
The 24XX256 will then issue an acknowledge and
transmit the 8-bit data word. The master will not
acknowledge the transfer, though it does generate a
Stop condition, which causes the 24XX256 to discon-
tinue transmission (Figure 8-2). After a random Read
command, the internal address counter will point to the
address location following the one that was just read.
24XX256 discontinues transmission (Figure 8-1).
8.3
Sequential Read
FIGURE 8-1:
S
CURRENT ADDRESS
READ
Sequential reads are initiated in the same way as a
random read except that after the 24XX256 transmits
the first data byte, the master issues an acknowledge
as opposed to the Stop condition used in a random
Bus Activity
Master
T
A
R
Control
Byte
Data
Byte
S
T
O
read. This acknowledge directs the 24XX256 to
transmit the next sequentially addressed 8-bit word
S 1 0 1 0 A AA 1
SDA Line
Bus Activity
T
2 1 0
A
C
K
N
O
A
C
K
P
P
(Figure 8-3). Following the final byte transmitted to the
master, the master will NOT generate an acknowledge,
but will generate a Stop condition. To provide sequen-
tial reads, the 24XX256 contains an internal Address
Pointer which is incremented by one at the completion
of each operation. This Address Pointer allows the
entire memory contents to be serially read during one
operation. The internal Address Pointer will
automatically roll over from address 7FFF to address
0000 if the master acknowledges the byte received
from the array address 7FFF.
FIGURE 8-2:
RANDOM READ
Bus Activity
Master
S
T
A
R
Control
Byte
Address
High Byte
Address
Low Byte
S
T
A
R
Control
Byte
Data
Byte
S
T
O
T
T
P
SDA Line
S 1 01 0 AAA 0
2 1 0
x
S 1 0 1 0 A A A 1
2 1 0
P
A
A
A
A
N
Bus Activity
x = “don’t care” bit
C
K
C
K
C
K
C
K
O
A
C
K
FIGURE 8-3:
SEQUENTIAL READ
Bus Activity
Master
Control
Byte
Data (n)
Data (n + 1)
Data (n + 2)
Data (n + x )
S
T
O
P
SDA Line
P
A
C
A
C
A
C
A
C
N
O
Bus Activity
K
K
K
K
A
C
K
DS21203R-page 12
? 1998-2011 Microchip Technology Inc.
相关PDF资料 |
PDF描述 |
|---|---|
| 25C160-I/P | IC EEPROM 16KBIT 3MHZ 8DIP |
| 745530-1 | CONN BACK COVER SLIDE ON DB9 |
| 25AA160/P | IC EEPROM 16KBIT 1MHZ 8DIP |
| 25AA160A-I/MS | IC EEPROM 16KBIT 10MHZ 8MSOP |
| XC6SLX100-L1FG484I | IC FPGA SPARTAN 6 484FGGBGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 24AA256UID-I/P | 功能描述:电可擦除可编程只读存储器 256K I2C EE EUI-48 EUI-64 Unique ID RoHS:否 制造商:Intersil 存储容量: 组织: 数据保留: 最大时钟频率: 最大工作电流: 工作电源电压: 最大工作温度: 安装风格: 封装 / 箱体: |
| 24AA256UID-I/SN | 功能描述:IC EEPROM 256KBIT 400KHZ 8SOIC 制造商:microchip technology 系列:- 包装:管件 零件状态:有效 格式 - 存储器:EEPROMs - 串行 存储器类型:EEPROM 存储容量:256K（32K x 8） 速度:100kHz，400kHz 接口:I2C，2 线串口 电压 - 电源:1.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C（TA） 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商器件封装:8-SOIC 标准包装:100 |
| 24AA256UID-I/ST | 功能描述:电可擦除可编程只读存储器 256K I2C EE EUI-48 EUI-64 Unique ID RoHS:否 制造商:Intersil 存储容量: 组织: 数据保留: 最大时钟频率: 最大工作电流: 工作电源电压: 最大工作温度: 安装风格: 封装 / 箱体: |
| 24AA256UIDT-I/SN | 功能描述:电可擦除可编程只读存储器 256K I2C EE EUI-48 EUI-64 Unique ID RoHS:否 制造商:Intersil 存储容量: 组织: 数据保留: 最大时钟频率: 最大工作电流: 工作电源电压: 最大工作温度: 安装风格: 封装 / 箱体: |
| 24AA256UIDT-I/ST | 功能描述:电可擦除可编程只读存储器 256K I2C EE EUI-48 EUI-64 Unique ID RoHS:否 制造商:Intersil 存储容量: 组织: 数据保留: 最大时钟频率: 最大工作电流: 工作电源电压: 最大工作温度: 安装风格: 封装 / 箱体: |
发布紧急采购，3分钟左右您将得到回复。