参数资料
型号: 24AA64FT-I/ST
厂商: Microchip Technology
文件页数: 7/36页
文件大小: 0K
描述: IC SRL EEPROM 8KX8 1.8V 8-TSSOP
标准包装: 2,500
格式 - 存储器: EEPROMs - 串行
存储器类型: EEPROM
存储容量: 64K (8K x 8)
速度: 100kHz,400kHz
接口: I²C,2 线串口
电源电压: 1.71 V ~ 5.5 V
工作温度: -40°C ~ 85°C
封装/外壳: 8-TSSOP(0.173",4.40mm 宽)
供应商设备封装: 8-TSSOP
包装: 带卷 (TR)
24AA64F/24LC64F/24FC64F
5.0
DEVICE ADDRESSING
FIGURE 5-1:
CONTROL BYTE FORMAT
A control byte is the first byte received following the
Start condition from the master device ( Figure 5-1 ).
The control byte consists of a four-bit control code. For
Read/Write Bit
Chip Select
the 24XX64F, this is set as ‘ 1010 ’ binary for read and
write operations. The next three bits of the control byte
Control Code
Bits
are the Chip Select bits (A2, A1, A0). The Chip Select
S
1
0
1
0
A2
A1
A0 R/W ACK
bits allow the use of up to eight 24XX64F devices on
the same bus and are used to select which device is
accessed. The Chip Select bits in the control byte must
Slave Address
correspond to the logic levels on the corresponding A2,
A1 and A0 pins for the device to respond. These bits
are, in effect, the three Most Significant bits of the word
address.
For the SOT-23 package, the address pins are not
available. During device addressing, the A2, A1 and A0
Start Bit
5.1
Acknowledge Bit
Contiguous Addressing Across
Multiple Devices
Chip Select bits ( Figure 5-2 ) should be set to ‘ 0 ’.
The last bit of the control byte defines the operation to
be performed. When set to a ‘ 1 ’, a read operation is
selected. When set to a ‘ 0 ’, a write operation is
selected. The next two bytes received define the
address of the first data byte ( Figure 5-2 ). Because
only A12...A0 are used, the upper-three address bits
are “don’t care” bits. The upper-address bits are
transferred first, followed by the Less Significant bits.
Following the Start condition, the 24XX64F monitors
the SDA bus, checking the device-type identifier being
transmitted. Upon receiving a ‘ 1010 ’ code and appro-
priate device-select bits, the slave device outputs an
Acknowledge signal on the SDA line. Depending on the
state of the R/W bit, the 24XX64F will select a read or
write operation.
The Chip Select bits A2, A1 and A0 can be used to
expand the contiguous address space for up to 512K
bits by adding up to eight 24XX64F devices on the
same bus. In this case, software can use A0 of the con-
trol byte as address bit A13; A1 as address bit A14; and
A2 as address bit A15. It is not possible to sequentially
read across device boundaries.
The SOT-23 package does not support multiple device
addressing on the same bus.
FIGURE 5-2:
ADDRESS SEQUENCE BIT ASSIGNMENTS
Control Byte
Address High Byte
Address Low Byte
0 R/W
1
0
1
0
A
2
A
1
A
x
x
x
A A A
12 11 10
A
9
A
8
A
7
?
?
?
?
?
?
A
0
Control
Code
Chip
Select
bits
x = “don’t care” bit
? 2009-2012 Microchip Technology Inc.
DS22154B-page 7
相关PDF资料
PDF描述
RMC65DRYN-S13 CONN EDGECARD 130PS .100 EXTEND
RSC65DRYH-S13 CONN EDGECARD 130POS .100 EXTEND
XA6SLX9-2CSG324I IC FPAG SPARTAN 6 9K 324CSGBGA
RMC65DRYH-S13 CONN EDGECARD 130PS .100 EXTEND
EEC50DTEI CONN EDGECARD 100POS .100 EYELET
相关代理商/技术参数
参数描述
24AA64-I/MNY 功能描述:电可擦除可编程只读存储器 64K 8K X 8 1.8V SER EE IND RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
24AA64-I/MNY-P9038V254MM 功能描述:- EEPROM Kit 制造商:idt, integrated device technology inc 系列:- 零件状态:有效 配件类型:EEPROM 套件 配套使用产品/相关产品:- 标准包装:1
24AA64-I/MS 功能描述:电可擦除可编程只读存储器 8kx8 - 1.8V RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
24AA64-I/MSG 功能描述:电可擦除可编程只读存储器 8kx8 - 1.8V Lead Free Package RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
24AA64-I/P 功能描述:电可擦除可编程只读存储器 8kx8 - 1.8V RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8