参数资料
| 型号： | 24LC014-I/SN |
| 厂商： | Microchip Technology |
| 文件页数： | 8/36页 |
| 文件大小： | 0K |
| 描述： | IC EEPROM 1KBIT 400KHZ 8SOIC |
| 产品培训模块： | I2C Serial EEPROM |
| 标准包装： | 100 |
| 格式 - 存储器： | EEPROMs - 串行 |
| 存储器类型： | EEPROM |
| 存储容量： | 1K (128 x 8) |
| 速度： | 400kHz |
| 接口： | I²C，2 线串口 |
| 电源电压： | 2.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOICN |
| 包装： | 管件 |
| 其它名称： | 24LC014I/SN |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
24AA014/24LC014
6.0
6.1
WRITE OPERATIONS
Byte Write
The higher order four bits of the word address remain
constant. If the master should transmit more than 16
bytes prior to generating the Stop condition, the
address counter will roll over and the previously
Following the Start signal from the master, the device
code(4 bits), the Chip Select bits (3 bits) and the R/W
bit (which is a logic low) are placed onto the bus by the
master transmitter. The device will acknowledge this
control byte during the ninth clock pulse. The next byte
transmitted by the master is the word address and will
be written into the Address Pointer of the 24AA014/
24LC014. After receiving another Acknowledge signal
received data will be overwritten. As with the byte write
operation, once the Stop condition is received, an inter-
nal write cycle will begin ( Figure 6-2 ). If an attempt is
made to write to the protected portion of the array when
the hardware write protection has been enabled, the
device will acknowledge the command, but no data will
be written. The write cycle time must be observed even
if write protection is enabled.
from the 24AA014/24LC014, the master device will
transmit the data word to be written into the addressed
memory location. The 24AA014/24LC014 acknowl-
edges again and the master generates a Stop
condition. This initiates the internal write cycle and the
24AA014/24LC014 will not generate Acknowledge
signals during this time ( Figure 6-1 ). If an attempt is
made to write to the protected portion of the array when
the hardware write protection has been enabled, the
device will acknowledge the command, but no data will
be written. The write cycle time must be observed even
if write protection is enabled.
Note:
Page write operations are limited to writ-
ing bytes within a single physical page,
regardless of the number of bytes
actually being written. Physical page
boundaries start at addresses that are
integer multiples of the page buffer size
(or ‘page size’) and end at addresses that
are integer multiples of [page size – 1]. If
a Page Write command attempts to write
across a physical page boundary, the
result is that the data wraps around to the
beginning of the current page (overwriting
6.2
Page Write
data previously stored there), instead of
being written to the next page, as might be
The write-control byte, word address and the first data
byte are transmitted to the 24AA014/24LC014 in the
same way as in a byte write. But instead of generating
a Stop condition, the master transmits up to 15 addi-
tional data bytes to the 24AA014/24LC014 that are
temporarily stored in the on-chip page buffer and will be
written into the memory once the master has transmit-
ted a Stop condition. Upon receipt of each word, the
four lower order Address Pointer bits are internally
incremented by one.
expected. It is therefore necessary that
the application software prevent page
write operations that would attempt to
cross a page boundary.
6.3 Write Protection
The WP pin must be tied to V CC or V SS . If tied to V CC ,
the entire array will be write-protected. If the WP pin is
tied to V SS , write operations to all address locations are
allowed.
The WP pin is not available on the SOT-23 package.
FIGURE 6-1:
BYTE WRITE
Bus Activity
Master
S
T
A
R
T
Control
Byte
Word
Address
Data
S
T
O
P
SDA Line
S
P
Bus Activity
DS21809G-page 8
A
C
K
A
C
K
A
C
K
? 2010 Microchip Technology Inc.
相关PDF资料 |
PDF描述 |
|---|---|
| 180-062-273L020 | CONN DB62 FEMALE HD CRIMP NICKEL |
| 24AA014-I/SN | IC EEPROM 1KBIT 400KHZ 8SOIC |
| 24AA024-I/SN | IC EEPROM 2KBIT 400KHZ 8SOIC |
| 24AA025-I/SN | IC EEPROM 2KBIT 400KHZ 8SOIC |
| 170-050-172-020 | CONN DB50 CRIMP MALE TIN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 24LC014T | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:1K I2C? Serial EEPROM |
| 24LC014T-E/MC | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:1K I2Ca?￠ Serial EEPROM |
| 24LC014T-E/MNY | 功能描述:电可擦除可编程只读存储器 1K 128 X 8 SERIAL EE 2.5V EXT RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| 24LC014T-E/MS | 功能描述:电可擦除可编程只读存储器 1K 128 X 8 SERIAL EE 2.5V EXT RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| 24LC014T-E/OT | 功能描述:电可擦除可编程只读存储器 1K 128 X 8 SERIAL EE 2.5V EXT RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
发布紧急采购，3分钟左右您将得到回复。