参数资料
型号: 24LC128T-I/ST14
厂商: Microchip Technology
文件页数: 7/38页
文件大小: 0K
描述: IC EEPROM 128KBIT 400KHZ 14TSSOP
标准包装: 2,500
格式 - 存储器: EEPROMs - 串行
存储器类型: EEPROM
存储容量: 128K (16K x 8)
速度: 400kHz
接口: I²C,2 线串口
电源电压: 2.5 V ~ 5.5 V
工作温度: -40°C ~ 85°C
封装/外壳: 14-TSSOP(0.173",4.40mm 宽)
供应商设备封装: 14-TSSOP
包装: 带卷 (TR)
其它名称: 24LC128TI/ST14
24AA128/24LC128/24FC128
5.0 DEVICE ADDRESSING
A control byte is the first byte received following the
Start condition from the master device (Figure 5-1).
The control byte consists of a 4-bit control code. For the
FIGURE 5-1:
CONTROL BYTE
FORMAT
Read/Write Bit
24XX128, this is set as ‘ 1010 ’ binary for read and write
operations. The next three bits of the control byte are
the Chip Select bits (A2, A1, A0). The Chip Select bits
Control Code
Chip Select
Bits
allow the use of up to eight 24XX128 devices on the
same bus and are used to select which device is
S
1
0
1
0
A2
A1
A0 R/W ACK
accessed. The Chip Select bits in the control byte must
correspond to the logic levels on the corresponding A2,
Slave Address
A1 and A0 pins for the device to respond. These bits
are, in effect, the three Most Significant bits of the word
address.
For the MSOP package, the A0 and A1 pins are not
connected. During device addressing, the A0 and A1
Start Bit
5.1
Acknowledge Bit
Contiguous Addressing Across
Multiple Devices
Chip Select bits (Figures 5-1 and 5-2) should be set to
‘ 0 ’. Only two 24XX128 MSOP packages can be
connected to the same bus.
The last bit of the control byte defines the operation to
be performed. When set to a one, a read operation is
selected. When set to a zero, a write operation is
selected. The next two bytes received define the
address of the first data byte (Figure 5-2). Because
only A13…A0 are used, the upper two address bits are
“don’t care” bits. The upper address bits are transferred
first, followed by the Less Significant bits.
Following the Start condition, the 24XX128 monitors
the SDA bus checking the device type identifier being
transmitted. Upon receiving a ‘ 1010 ’ code and
appropriate device select bits, the slave device outputs
an Acknowledge signal on the SDA line. Depending on
the state of the R/W bit, the 24XX128 will select a read
or write operation.
The Chip Select bits A2, A1 and A0 can be used to
expand the contiguous address space for up to 1 Mbit
by adding up to eight 24XX128 devices on the same
bus. In this case, software can use A0 of the control
byte as address bit A14; A1 as address bit A15; and A2
as address bit A16. It is not possible to sequentially
read across device boundaries.
For the MSOP package, up to two 24XX128 devices
can be added for up to 256 Kbit of address space. In
this case, software can use A2 of the control byte as
address bit A16. Bits A0 (A14) and A1 (A15) of the
control byte must always be set to logic ‘ 0 ’ for the
MSOP.
FIGURE 5-2:
ADDRESS SEQUENCE BIT ASSIGNMENTS
Control Byte
Address High Byte
Address Low Byte
0 R/W
1
0
1
0
A
2
A
1
A
x
x
A A A A
13 12 11 10
A
9
A
8
A
7
?
?
?
?
?
?
A
0
Control
Code
Chip
Select
Bits
x = “don’t care” bit
? 2010 Microchip Technology Inc.
DS21191S-page 7
相关PDF资料
PDF描述
FF0396SA1-R2000 CONN FFC/FPC 0.5MM 96POS R/A SMD
93AA46X-I/SN IC EEPROM 1KBIT 2MHZ 8SOIC
FA5S020HP1 CONN FFC/FPC 0.5MM 20POS R/A SMD
FF0368SA1 CONN FFC/FPC 0.5MM 68POS R/A SMD
FB3S021C11 CONN FPC/FFC 21POS 0.3MM R/A SMD
相关代理商/技术参数
参数描述
24LC16 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:8K/16K 2.5V SPI O Bus Serial EEPROM
24LC16/P 制造商:Rochester Electronics LLC 功能描述:- Bulk
24LC160-IP 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:8K/16K 2.5V SPI O Bus Serial EEPROM
24LC160-ISN 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:8K/16K 2.5V SPI O Bus Serial EEPROM
24LC160-P 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:8K/16K 2.5V SPI O Bus Serial EEPROM