参数资料
| 型号： | 24LC22A-I/SN |
| 厂商： | Microchip Technology |
| 文件页数： | 5/24页 |
| 文件大小： | 0K |
| 描述： | IC EEPROM 2KBIT 400KHZ 8SOIC |
| 产品培训模块： | I2C Serial EEPROM |
| 标准包装： | 100 |
| 格式 - 存储器： | EEPROMs - 串行 |
| 存储器类型： | EEPROM |
| 存储容量： | 2K (256 x 8) |
| 速度： | 100kHz，400kHz |
| 接口： | I²C，2 线串口 |
| 电源电压： | 2.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOICN |
| 包装： | 管件 |
| 其它名称： | 24LC22A-I/SNG 24LC22A-I/SNG-ND 24LC22AI/SN |
24LC22A
3.0 BIDIRECTIONAL MODE
Before the 24LC22A can be switched into the Bidirec-
tional mode (Figure 3-1), it must enter the Transition
mode, which is done by applying a valid high-to-low
transition on the Bidirectional mode clock (SCL). As
soon it enters the Transition mode, it looks for a control
byte ‘1010 000X’ on the I 2 C? bus, and starts to
count pulses on VCLK. Any high-to-low transition on
the SCL line will reset the count. If it sees a pulse count
of 128 on VCLK while the SCL line is idle, it will revert
back to the Transmit-Only mode, and transmit its con-
tents starting with the Most Significant bit in address
00h. However, if it detects the control byte on the I 2 C
bus, (Figure 3-2) it will switch to the in the Bidirectional
mode. Once the device has made the transition to the
Bidirectional mode, the only way to switch the device
back to the Transmit-Only mode is to remove power
from the device. The mode transition process is shown
in detail in Figure 3-3.
Once the device has switched into the Bidirectional
mode, the VCLK input is disregarded, with the excep-
tion that a logic high level is required to enable write
capability. In Bidirectional mode the user has access to
the entire 2K array, whereas in the Transmit-Only mode
the user can only access the first 1K. This mode sup-
ports a two-wire Bidirectional data transmission proto-
col (I 2 C). In this protocol, a device that sends data on
the bus is defined to be the transmitter, and a device
that receives data from the bus is defined to be the
receiver. The bus must be controlled by a master
device that generates the Bidirectional mode clock
(SCL), controls access to the bus and generates the
Start and Stop conditions, while the 24LC22A acts as
the slave. Both master and slave can operate as trans-
mitter or receiver, but the master device determines
which mode is activated. In the Bidirectional mode, the
24LC22A only responds to commands for device
‘1010 000X’ .
FIGURE 3-1:
MODE TRANSITION WITH RECOVERY TO TRANSMIT-ONLY MODE
MODE
Transmit-Only
T VHZ
Bidirectional
Recovery to Transmit-Only mode
SCL
(MSB of data in 00h)
SDA
Bit 8
VCLK count =
1
2
3
4
12 7 12 8
VCLK
FIGURE 3-2:
SUCCESSFUL MODE TRANSITION TO BIDIRECTIONAL MODE
Transmit-Only
MODE
SCL
Transition mode with possibility to return to Transmit-Only mode
Bidirectional
permanently
SDA
S
1
0
1
0
0
0
0
0
ACK
VCLK count =
1
2
n
0
VCLK
n < 128
? 2007 Microchip Technology Inc.
DS21683B-page 5
相关PDF资料 |
PDF描述 |
|---|---|
| XC6SLX4-L1CSG225I | IC FPGA SPARTAN 6 3K 225CSGBGA |
| 11LC160-E/P | IC EEPROM 16K FLASH 8PDIP |
| 93C56A-I/SN | IC EEPROM 2KBIT 2MHZ 8SOIC |
| XC6SLX4-3CSG225I | IC FPGA SPARTAN 6 3K 225CSGBGA |
| XA3S200-4VQG100Q | IC FPGA SPARTAN-3 200K 100-VQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 24LC22AT-I/SN | 功能描述:电可擦除可编程只读存储器 VESA E-EDID RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| 24LC22AT-I/SNG | 功能描述:电可擦除可编程只读存储器 VESA E-EDID Lead Free Package RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| 24LC256-E/MF | 功能描述:电可擦除可编程只读存储器 32kx8 - 2.5V RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| 24LC256E/MS | 制造商:Microchip Technology 功能描述:EEPROM Serial-I2C 256K-Bit 32K x 8 3.3V/5V 8-Pin MSOP Tube |
| 24LC256-E/MS | 功能描述:电可擦除可编程只读存储器 32kx8 - 2.5V RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
发布紧急采购，3分钟左右您将得到回复。