参数资料
型号: 24LC32AF-I/SN
厂商: Microchip Technology
文件页数: 7/30页
文件大小: 0K
描述: IC SRL EEPROM 4KX8 2.5V 8-SOIC
标准包装: 100
格式 - 存储器: EEPROMs - 串行
存储器类型: EEPROM
存储容量: 32K (4K x 8)
速度: 400kHz
接口: I²C,2 线串口
电源电压: 2.5 V ~ 5.5 V
工作温度: -40°C ~ 85°C
封装/外壳: 8-SOIC(0.154",3.90mm 宽)
供应商设备封装: 8-SOICN
包装: 管件
24AA32AF/24LC32AF
5.0
DEVICE ADDRESSING
an Acknowledge signal on the SDA line. Depending on
the state of the R/W bit, the 24XX32AF will select a
A control byte is the first byte received following the
Start condition from the master device (Figure 5-1).
read or write operation.
The control byte consists of a four-bit control code. For
the 24XX32AF, this is set as ‘ 1010 ’ binary for read and
write operations. The next three bits of the control byte
are the Chip Select bits (A2, A1, A0). The Chip Select
FIGURE 5-1:
CONTROL BYTE FORMAT
Read/Write Bit
bits allow the use of up to eight 24XX32AF devices on
the same bus and are used to select which device is
accessed. The Chip Select bits in the control byte must
Control Code
Chip Select
Bits
correspond to the logic levels on the corresponding A2,
S
1
0
1
0
A2 A1 A0 R/W ACK
A1 and A0 pins for the device to respond. These bits
are in effect the three Most Significant bits of the word
address.
Slave Address
For the SOT-23 package, the address pins are not
available. During device addressing, the A1, A2, and
A0 Chip Select bits (Figure 5-2) should be set to ‘ 0 ’.
Start Bit
Acknowledge Bit
The last bit of the control byte defines the operation to
5.1
Contiguous Addressing Across
be performed. When set to a ‘ 1 ’, a read operation is
selected. When set to a zero, a write operation is
selected. The next two bytes received define the
address of the first data byte (Figure 5-2). Because
only A11 to A0 are used, the upper four address bits are
“don’t care” bits. The upper address bits are transferred
first, followed by the Less Significant bits.
Following the Start condition, the 24XX32AF monitors
the SDA bus checking the device type identifier being
transmitted and, upon receiving a ‘ 1010 ’ code and
appropriate device select bits, the slave device outputs
Multiple Devices
The Chip Select bits A2, A1 and A0 can be used to
expand the contiguous address space for up to 256K
bits by adding up to eight 24XX32AF devices on the
same bus. In this case, software can use A0 of the con-
trol byte as address bit A12; A1 as address bit A13; and
A2 as address bit A14. It is not possible to sequentially
read across device boundaries.
The SOT-23 package does not support multiple device
addressing on the same bus.
FIGURE 5-2:
ADDRESS SEQUENCE BIT ASSIGNMENTS
Control Byte
Address High Byte
Address Low Byte
0 R/W
1
0
1
0
A
2
A
1
A
x
x
x
x
A A
11 10
A
9
A
8
A
7
?
?
?
?
?
?
A
0
Control
Code
Chip
Select
Bits
x = “don’t care” bit
? 2009 Microchip Technology Inc.
DS22184A-page 7
相关PDF资料
PDF描述
EP4SGX360NF45C2N IC STRATIX IV FPGA 360K 1932FBGA
24LC16BHT-E/SN IC EEPROM 16KBIT 400KHZ 8SOIC
EP4S100G2F40I2N IC STRATIX IV FPGA 230K 1517FBGA
24LC04BT-E/MNY IC EEPROM 4KBIT 400KHZ 8TDFN
24LC04BHT-E/MNY IC EEPROM 4KBIT 400KHZ 8TDFN
相关代理商/技术参数
参数描述
24LC32AFT-E/MNY 功能描述:电可擦除可编程只读存储器 32K 4K X 8 2.5V SER EE EX 1/4AWP RPO RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
24LC32AFT-E/MS 功能描述:电可擦除可编程只读存储器 32K 4K X 8 2.5V SER EE EXT 1/4AWP RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
24LC32AFT-E/OT 功能描述:电可擦除可编程只读存储器 32K 4K X 8 2.5V SER EE EXT 1/4AWP RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
24LC32AFT-E/SM 功能描述:电可擦除可编程只读存储器 32K 4K X 8 2.5V SER EE EXT 1/4AWP RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
24LC32AFT-E/SN 功能描述:电可擦除可编程只读存储器 32K 4K X 8 2.5V SER EE EXT 1/4AWP RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8