- 您现在的位置：买卖IC网 > PDF目录4302 > 24LC32AFT-I/SN (Microchip Technology)IC SRL EEPROM 4KX8 2.5V 8-SOIC PDF资料下载
参数资料
| 型号： | 24LC32AFT-I/SN |
| 厂商： | Microchip Technology |
| 文件页数： | 6/30页 |
| 文件大小： | 0K |
| 描述： | IC SRL EEPROM 4KX8 2.5V 8-SOIC |
| 标准包装： | 3,300 |
| 格式 - 存储器： | EEPROMs - 串行 |
| 存储器类型： | EEPROM |
| 存储容量： | 32K (4K x 8) |
| 速度： | 400kHz |
| 接口： | I²C，2 线串口 |
| 电源电压： | 2.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOICN |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
24AA32AF/24LC32AF
3.0
FUNCTIONAL DESCRIPTION
4.4
Data Valid (D)
The 24XX32AF supports a bidirectional, 2-wire bus and
data transmission protocol. A device that sends data
onto the bus is defined as transmitter, while a device
receiving data is defined as a receiver. The bus has to
be controlled by a master device which generates the
Serial Clock (SCL), controls the bus access and gener-
ates the Start and Stop conditions, while the 24XX32AF
works as slave. Both master and slave can operate as
transmitter or receiver, but the master device
determines which mode is activated.
The state of the data line represents valid data when,
after a Start condition, the data line is stable for the
duration of the high period of the clock signal.
The data on the line must be changed during the low
period of the clock signal. There is one clock pulse per
bit of data.
Each data transfer is initiated with a Start condition and
terminated with a Stop condition. The number of data
bytes transferred between Start and Stop conditions is
determined by the master device and is, theoretically,
4.0
BUS CHARACTERISTICS
unlimited (although only the last thirty-two bytes will be
stored when doing a write operation). When an over-
The following bus protocol has been defined:
? Data transfer may be initiated only when the bus
write does occur, it will replace data in a first-in first-out
(FIFO) fashion.
is not busy.
? During data transfer, the data line must remain
4.5
Acknowledge
stable whenever the clock line is high. Changes in
the data line while the clock line is high will be
interpreted as a Start or Stop condition.
Accordingly, the following bus conditions have been
Each receiving device, when addressed, is obliged to
generate an Acknowledge after the reception of each
byte. The master device must generate an extra clock
pulse which is associated with this Acknowledge bit.
defined (Figure 4-1).
Note:
The 24XX32AF does not generate any
Acknowledge bits if an internal
4.1
Bus Not Busy (A)
programming cycle is in progress.
Both data and clock lines remain high.
The device that acknowledges, has to pull down the
SDA line during the Acknowledge clock pulse in such a
4.2
Start Data Transfer (B)
way that the SDA line is stable low during the high
period of the Acknowledge related clock pulse. Of
A high-to-low transition of the SDA line while the clock
(SCL) is high determines a Start condition. All
commands must be preceded by a Start condition.
course, setup and hold times must be taken into
account. During reads, a master must signal an end of
data to the slave by not generating an Acknowledge bit
on the last byte that has been clocked out of the slave.
4.3
Stop Data Transfer (C)
In this case, the slave (24XX32AF) will leave the data
line high to enable the master to generate the Stop
A low-to-high transition of the SDA line while the clock
(SCL) is high determines a Stop condition. All
operations must be ended with a Stop condition.
condition.
FIGURE 4-1:
DATA TRANSFER SEQUENCE ON THE SERIAL BUS
(A)
(B)
(D)
(D)
(C)
(A)
SCL
SDA
Start
Condition
Address or
Acknowledge
Data
Allowed
Stop
Condition
DS22184A-page 6
Valid
to Change
? 2009 Microchip Technology Inc.
相关PDF资料 |
PDF描述 |
|---|---|
| EP4SGX360NF45I3N | IC STRATIX IV FPGA 360K 1932FBGA |
| 24LC32AF-I/SN | IC SRL EEPROM 4KX8 2.5V 8-SOIC |
| EP4SGX360NF45C2N | IC STRATIX IV FPGA 360K 1932FBGA |
| 24LC16BHT-E/SN | IC EEPROM 16KBIT 400KHZ 8SOIC |
| EP4S100G2F40I2N | IC STRATIX IV FPGA 230K 1517FBGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 24LC32A-I/MNY | 功能描述:电可擦除可编程只读存储器 32K 4K X 8 2.5V SER EE IND RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| 24LC32A-I/MS | 功能描述:电可擦除可编程只读存储器 4kx8 - 5V - 2.5V RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| 24LC32A-I/MSG | 功能描述:电可擦除可编程只读存储器 4kx8 - 5V - 2.5V Lead Free Package RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| 24LC32A-I/P | 功能描述:电可擦除可编程只读存储器 4kx8 - 5V - 2.5V RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| 24LC32A-I/P | 制造商:Microchip Technology Inc 功能描述:IC EEPROM SERIAL 32K |
发布紧急采购，3分钟左右您将得到回复。