参数资料
| 型号： | 24LC512-E/MF |
| 厂商： | Microchip Technology |
| 文件页数： | 7/36页 |
| 文件大小： | 0K |
| 描述： | IC EEPROM 512KBIT 400KHZ 8DFN |
| 产品培训模块： | I2C Serial EEPROM |
| 标准包装： | 60 |
| 格式 - 存储器： | EEPROMs - 串行 |
| 存储器类型： | EEPROM |
| 存储容量： | 512K (64K x 8) |
| 速度： | 400kHz |
| 接口： | I²C，2 线串口 |
| 电源电压： | 2.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 8-VDFN 裸露焊盘 |
| 供应商设备封装： | 8-DFN-S（6x5） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
24AA512/24LC512/24FC512
4.0
BUS CHARACTERISTICS
4.5
Acknowledge
The following bus protocol has been defined:
? Data transfer may be initiated only when the bus
is not busy.
? During data transfer, the data line must remain
stable whenever the clock line is high. Changes in
the data line, while the clock line is high, will be
interpreted as a Start or Stop condition.
Accordingly, the following bus conditions have been
defined (Figure 4-1).
Each receiving device, when addressed, is obliged to
generate an Acknowledge signal after the reception of
each byte. The master device must generate an extra
clock pulse which is associated with this Acknowledge
bit. See Figure 4-2 for acknowledge timing.
Note: The 24XX512 does not generate any
Acknowledge bits if an internal programming
cycle is in progress.
A device that acknowledges must pull down the SDA
line during the Acknowledge clock pulse in such a way
4.1
Bus Not Busy (A)
that the SDA line is stable low during the high period of
the acknowledge related clock pulse. Of course, setup
Both data and clock lines remain high.
4.2 Start Data Transfer (B)
A high-to-low transition of the SDA line while the clock
(SCL) is high determines a Start condition. All
commands must be preceded by a Start condition.
and hold times must be taken into account. During
reads, a master must signal an end of data to the slave
by NOT generating an Acknowledge bit on the last byte
that has been clocked out of the slave. In this case, the
slave (24XX512) will leave the data line high to enable
the master to generate the Stop condition.
4.3
Stop Data Transfer (C)
A low-to-high transition of the SDA line while the clock
(SCL) is high determines a Stop condition. All
operations must end with a Stop condition.
4.4
Data Valid (D)
The state of the data line represents valid data when,
after a Start condition, the data line is stable for the
duration of the high period of the clock signal.
The data on the line must be changed during the low
period of the clock signal. There is one bit of data per
clock pulse.
Each data transfer is initiated with a Start condition and
terminated with a Stop condition. The number of the
data bytes transferred between the Start and Stop
conditions is determined by the master device.
? 2010 Microchip Technology Inc.
DS21754M-page 7
相关PDF资料 |
PDF描述 |
|---|---|
| 24LC512T-E/MF | IC EEPROM 512KBIT 400KHZ 8DFN |
| SST25WF080-75-4I-SAF-T | I CFLASH SER 8MN 75MHZ SPI 8SOIC |
| SST39VF040-70-4I-NHE-T | IC FLASH MPF 4MBIT 70NS 32PLCC |
| SST39VF040-70-4C-NHE-T | IC FLASH MPF 4MBIT 70NS 32PLCC |
| SST25VF016B-75-4I-QAF-T | IC FLASH SER 16M 75MHZ SPI 8WSON |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 24LC512-I/MF | 功能描述:电可擦除可编程只读存储器 64kx8 - 2.5V RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| 24LC512-I/MF | 制造商:Microchip Technology Inc 功能描述:Serial EEPROM IC |
| 24LC512-I/MS | 制造商:Microchip Technology Inc 功能描述:512K, 64K X 8, 2.5V SER EE, IND - Rail/Tube 制造商:Microchip Technology Inc 功能描述:IC EEPROM 512KBIT 400KHZ 8MSOP 制造商:Microchip Technology Inc 功能描述:512K, 64K X 8, 2.5V SER EE, IND, 8 MSOP 3x3mm TUBE |
| 24LC512-I/P | 功能描述:电可擦除可编程只读存储器 64kx8 - 2.5V RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| 24LC512-I/P | 制造商:Microchip Technology Inc 功能描述:EEPROM SERIAL 512K 24LC512 DIP8 |
发布紧急采购，3分钟左右您将得到回复。