2532 (B&K Precision) Datasheet资料下载 PDF(60/70 页)

您现在的位置：买卖IC网 > Datasheet目录647 > 2532 (B&K Precision)OSCOPE 40MHZ DIGITAL STORAGE Datasheet资料下载

参数资料

Chapter 5 Prompt messages and troubleshooting hints

5.1 Prompt messages:

■ Trig volt level at limit ： When turning the trigger knob, Alerts the user that the trigger level reached

its limit

■ Horizon position at limit ： When turning the horizontal position knob , alerts user that the horizontal

position reached its limit

■ Volts/Div at limit ： Alerts the user that the vertical volt/Div knob was adjusted to the min (2mV/div)

or maximum ( 5V/div ) value

■ Volts position at limit ： When turning the vertical position knob , alerts user that the vertical knob

reached its limit.

■ Sec/Div at limit ： Prompts the user that the Volts/Div is at full range while turning the vertical scale

knob.

■ Functions isn’t useable ： Function not supported in this mode. (Example: Reference mode is not

available in YX format)

■ No signal! ： The system could not detect a suitable signal ( used in the auto set )

■ Adjust at limit : You could adjust the pulse width with the ADJUST knob until the pulse width has

reached the min of 20.0ns or max 10.0s limit.

5.2 Troubleshooting

1. If the screen remains dark after the oscilloscope is powered on, try the following:

a) Check if the power cable is connected properly

b) Ensure the power switch is turned on.

c) After verifying a) and b) restart the oscilloscope.

d) If the oscilloscope is still not working, contact your authorized B+K Precision distributor.

2. If there is no signal displayed on the screen, do the following :

a) Verify that the probe or BNC cable is properly connected to CH1 or CH2.

b) Make sure your BNC cable or probe is connected to a life signal

3. If the signal amplitude is 10 times higher/lower than the actual signal, try the following:

Check the attenuation factor and make sure it matches the probe attenuation setting

4. If the waveform is displayed, but not stable, do the following ：

Make sure signal source and trigger setup match.

Check the trigger mode: Common signals should use Edge trigger. Video signals should the Video

相关PDF资料	PDF描述
2542B	OSCOPE 100MHZ 1GSA/S DGTL STORGE
25449NAB	SWITCH MINI SLIDE
2630	SPECTRUM ANALYZR W/TRACK 1.05GHZ
2630	BNC FEMALE-ALLIGATOR TEST CLIPS
2631	BNC FEMALE-MINIGATOR TEST CLIPS

相关代理商/技术参数	参数描述
25-320	功能描述:WR COMB LNG 6PT 5/8 FP 制造商:apex tool group 系列:* 零件状态:在售标准包装:1
25320-100	制造商:DANAHER - INDUSTRIAL/SPECIALTY 功能描述:25320 BK199
253-2015	功能描述:扬声器与变频器 SPK 8 OHM 40MM .2W RoHS:否制造商:PUI Audio 产品:Speakers 类型:Electromagnetic 频率:900 Hz to 12 kHz 声压级:88 dBA 阻抗:8 Ohms 功率额定值:1.2 W 形状:Round 端接类型:Solder Pad 直径:15 mm 长度: 宽度: 深度:4.4 mm 磁体材料:Neodymium Iron Boran (NdFeB) 圆锥体材料:Mylar
253-2015-RO	功能描述:扬声器与变频器 8 OHM .2W 40MM RoHS:否制造商:PUI Audio 产品:Speakers 类型:Electromagnetic 频率:900 Hz to 12 kHz 声压级:88 dBA 阻抗:8 Ohms 功率额定值:1.2 W 形状:Round 端接类型:Solder Pad 直径:15 mm 长度: 宽度: 深度:4.4 mm 磁体材料:Neodymium Iron Boran (NdFeB) 圆锥体材料:Mylar
253201B	制造商:ITF 制造商全称:ITF 功能描述:125.0 MHz SAW Filter

发布紧急采购，3分钟左右您将得到回复。

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购