- 您现在的位置：买卖IC网 > PDF目录22313 > 2539-SC/APC (3M)SPLICE FIBRLOK II W/SC-APC PIGTL PDF资料下载
参数资料
| 型号： | 2539-SC/APC |
| 厂商： | 3M |
| 文件页数： | 4/4页 |
| 文件大小： | 0K |
| 描述： | SPLICE FIBRLOK II W/SC-APC PIGTL |
| 标准包装： | 12 |
| 系列： | Fibrlok™ II |
| 类型： | 接线头 |
| 技术规格： | 0.25mm ~ 0.90mm 直径线缆，38.1mm 长 |
| 特点： | SC/APC 包括引出线 |
| 其它名称： | 0-00-51115-22860-5 00051115228605 2539SC/APC 5111522860 51115228605 80-6113-2239-9 80611322399 |
7.8 Grasp the left fiber about 2 inches from the holder and push the
fiber in until it bows about 1/8 to 1/4 inch (3mm to 6mm). Push
down on the actuation lever until the Fibrlok II Splice is actuated.
An audible click can be heard and you should feel the splice cap
snap down into place when completely closed. The cap should be
level with the Fibrlok splice top surface.
7.9 Release the bow in the fiber and fully close the left buffer clamp.
Again, you will hear an audible snap.
8.0 Fiber Repositioning
8.1 If high loss is observed after the splice has been actuated, it is possible that the fiber ends are separated.
In this case, lift the splice cap and reposition the fiber ends, as instructed below.
8.2 While the splice is still in the holder assembly, lift the actuation
lever and insert the cap removal tool over the splice cap. Grasp
both sides of the splice holder base and lift the cap up and off the
splice while gently rocking lengthwise. Replace the cap parallel
to the top, but raised about 1mm (0.04 inch) as it snaps into
place.
8.3 Carefully reposition fiber. Refer to section 7.0 for proper
fiber centering and splice actuation.
8.4 Place splice cap back on the Fibrlok splice and push down the
actuation lever until cap has been fully actuated.
8.5 If after two attempts, an acceptable splice loss is not obtained,
remove fibers and replace the Fibrlok splice with a new splice.
Redo fiber preparation (section 5) by re-stripping, cleaning, and
cleaving both fibers. Then repeat steps in section 7.
8.6 Upon completion, the actuation lever can be removed and
discarded if desired.
Rev B
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6402IRZ-TK | IC REG TRPL BCK/LINEAR 28QFN |
| ISL6402IRZ-T | IC REG TRPL BCK/LINEAR 28QFN |
| VLCF5020T-2R7N2R2-3 | INDUCTOR POWER 2.7UH 2.2A SMD |
| ISL6402IRZ | IC REG TRPL BCK/LINEAR 28QFN |
| MIC5891YN | IC DRVR LATCH 8BIT SER IN 16DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 253-A | 功能描述:罩类、盒类及壳类产品 5.63 x 3.25 x 2.55 Almond RoHS:否 制造商:Bud Industries 产品:Boxes 外部深度:6.35 mm 外部宽度:6.35 mm 外部高度:2.56 mm NEMA 额定值: IP 等级: 材料:Acrylonitrile Butadiene Styrene (ABS) 颜色:Red |
| 253A103A45NA | 制造商:CTS 制造商全称:CTS Corporation 功能描述:Two Axis, Ministick Controller With Optional Momentary Switch |
| 253A103A45NB | 制造商:CTS 制造商全称:CTS Corporation 功能描述:Two Axis, Ministick Controller With Optional Momentary Switch |
| 253A103A50NA | 制造商:CTS 制造商全称:CTS Corporation 功能描述:Two Axis, Ministick Controller With Optional Momentary Switch |
| 253A103A50NB | 制造商:CTS 制造商全称:CTS Corporation 功能描述:Two Axis, Ministick Controller With Optional Momentary Switch |
发布紧急采购，3分钟左右您将得到回复。