- 您现在的位置：买卖IC网 > PDF目录22316 > 2539 (3M)SPLICE W/HOLDER FIBRLOK II UNIV PDF资料下载
参数资料
| 型号： | 2539 |
| 厂商： | 3M |
| 文件页数： | 3/4页 |
| 文件大小： | 0K |
| 描述： | SPLICE W/HOLDER FIBRLOK II UNIV |
| 标准包装： | 60 |
| 系列： | Fibrlok™ II |
| 类型： | 接线头 |
| 技术规格： | 0.25mm ~ 0.90mm 直径线缆，38.1mm 长 |
| 其它名称： | 0-00-51115-21516-2 00051115215162 5111521516 51115215162 80-6113-2005-4 80611320054 |
Note: Cleavers must be in good operating condition and used per the manufacturer’s instructions. They
should provide consistent cleave-to-coating lengths within +/- 0.5mm. Acceptable cleavers will produce
cleaved ends within 0.5° of perpendicular (typical always <1 °), free from major defects.
5.5 Cleave lengths can be confirmed on the 12.5mm length
gauge. Cleave should be within the window.
6.0 3M Fibrlok II Splice/Holder Pigtail Assembly
2539 SC/APC and 2539 SC/UPC
6.1 Cut off rubber band, position actuation lever over splice, and
lift both buffer clamps to the “up”position.
6.2 Confirm that buffer on pigtail is fully inserted inside
splice and follow steps 7.2 through 7.9.
7.0 Splice/Holder Assembly 2539
Note: Always insert the fiber first on the right (actuation lever
side) of the splice/holder.
7.1 Holding the fiber approximately ? inch (13mm) from the
bare glass, insert cleaved fiber into the guide on the right
(actuation lever side) of the splice/holder until it stops inside
the Fibrlok II splice.
Note: Push fiber straight into the fiber alignment guide, not at
an angle. Bare glass should not be visible outside of the splice. If
bare glass is visible, pull back slightly on the fiber and continue
insertion until resistance is met. Do not fully remove fibers from
splice after initial insertion.
7.2 Carefully mark the buffer at the right edge of the base.
7.3 Prepare second fiber (strip, clean and cleave) as described in
section 5.
7.4 Holding the fiber approximately ? inch (13mm) from the
bare glass, insert second fiber into the guide on the left side
(opposite actuation lever) of the splice/holder until it stops
inside the Fibrlok II splice.
7.5 While sliding the second fiber into the splice, the mark on the
first fiber should move outwards 1/8 inch (3mm) showing the
fiber ends are in contact. If this is not observed, one or both
fibers has a bad/short cleave. Remove one fiber and re-strip,
clean, re-cleave and insert back into the splice. If contact is
still not correct, repeat procedure for second fiber.
Note: To prevent contamination, never fully remove and re-
insert a cleaved end back into a splice without first re-stripping
and re-cleaving.
7.6 Center both fiber cleaves by repositioning the mark on the first
fiber half way back to its original position.
7.7 Once the fibers are centered, fully close the right buffer clamp.
You will hear an audible snap.
相关PDF资料 |
PDF描述 |
|---|---|
| GBM06DTMS-S189 | CONN EDGECARD 12POS R/A .156 SLD |
| AMM24DRTN-S13 | CONN EDGECARD 48POS DIP .156 SLD |
| GBM08DTMS | CONN EDGECARD 16POS R/A .156 SLD |
| AMM24DRTH-S13 | CONN EDGECARD 48POS DIP .156 SLD |
| GEM15DSUS | CONN EDGECARD 30POS DIP .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 25390 BK005 | 功能描述:10 Conductor Multi-Conductor Cable Black 18 AWG Foil 100.0' (30.5m) 制造商:alpha wire 系列:Xtra-Guard? 2 零件状态:有效 电缆类型:多芯 导体数:10 线规:18 AWG 导线股数:16/30 导体材料:铜，镀锡 护套（绝缘）材料:聚氨脂（PU） 护套（绝缘）直径:0.388"（9.85mm） 屏蔽类型:箔 长度:100.0'（30.5m） 套管颜色:黑 等级:ISO 10993，UL 式 20668 特性:生物相容性，加蔽线，拉绳 电压:300V 工作温度:-30°C ~ 90°C 使用:- 导体绝缘:聚氯乙烯（PVC） 护套（绝缘）厚度:0.032"（0.81mm） 屏蔽材料:铝 屏蔽范围:1 标准包装:10 |
| 25390/15 BK005 | 功能描述:15 Conductor Multi-Conductor Cable Black 18 AWG Foil 100.0' (30.5m) 制造商:alpha wire 系列:Xtra-Guard? 2 零件状态:有效 电缆类型:多芯 导体数:15 线规:18 AWG 导线股数:16/30 导体材料:铜，镀锡 护套（绝缘）材料:聚氨脂（PU） 护套（绝缘）直径:0.437"（11.10mm） 屏蔽类型:箔 长度:100.0'（30.5m） 套管颜色:黑 等级:ISO 10993，UL 式 20668 特性:生物相容性，加蔽线，拉绳 电压:300V 工作温度:-30°C ~ 90°C 使用:- 导体绝缘:聚氯乙烯（PVC） 护套（绝缘）厚度:0.032"（0.81mm） 屏蔽材料:铝 屏蔽范围:1 标准包装:10 |
| 25390/20 BK005 | 功能描述:20 Conductor Multi-Conductor Cable Black 18 AWG Foil 100.0' (30.5m) 制造商:alpha wire 系列:Xtra-Guard? 2 零件状态:有效 电缆类型:多芯 导体数:20 线规:18 AWG 导线股数:16/30 导体材料:铜，镀锡 护套（绝缘）材料:聚氨脂（PU） 护套（绝缘）直径:0.488"（12.40mm） 屏蔽类型:箔 长度:100.0'（30.5m） 套管颜色:黑 等级:ISO 10993，UL 式 20668 特性:生物相容性，加蔽线，拉绳 电压:300V 工作温度:-30°C ~ 90°C 使用:- 导体绝缘:聚氯乙烯（PVC） 护套（绝缘）厚度:0.032"（0.81mm） 屏蔽材料:铝 屏蔽范围:1 标准包装:10 |
| 25390/25 BK005 | 功能描述:25 Conductor Multi-Conductor Cable Black 18 AWG Foil 100.0' (30.5m) 制造商:alpha wire 系列:Xtra-Guard? 2 零件状态:有效 电缆类型:多芯 导体数:25 线规:18 AWG 导线股数:16/30 导体材料:铜，镀锡 护套（绝缘）材料:聚氨脂（PU） 护套（绝缘）直径:0.588"（14.94mm） 屏蔽类型:箔 长度:100.0'（30.5m） 套管颜色:黑 等级:ISO 10993，UL 式 20668 特性:生物相容性，加蔽线，拉绳 电压:300V 工作温度:-30°C ~ 90°C 使用:- 导体绝缘:聚氯乙烯（PVC） 护套（绝缘）厚度:0.053"（1.35mm） 屏蔽材料:铝 屏蔽范围:1 标准包装:10 |
| 25390/30 BK005 | 功能描述:30 Conductor Multi-Conductor Cable Black 18 AWG Foil 100.0' (30.5m) 制造商:alpha wire 系列:Xtra-Guard? 2 零件状态:有效 电缆类型:多芯 导体数:30 线规:18 AWG 导线股数:16/30 导体材料:铜，镀锡 护套（绝缘）材料:聚氨脂（PU） 护套（绝缘）直径:0.621"（15.77mm） 屏蔽类型:箔 长度:100.0'（30.5m） 套管颜色:黑 等级:ISO 10993，UL 式 20668 特性:生物相容性，加蔽线，拉绳 电压:300V 工作温度:-30°C ~ 90°C 使用:- 导体绝缘:聚氯乙烯（PVC） 护套（绝缘）厚度:0.053"（1.35mm） 屏蔽材料:铝 屏蔽范围:1 标准包装:10 |
发布紧急采购，3分钟左右您将得到回复。