- 您现在的位置：买卖IC网 > PDF目录18664 > 2559 (3M)SPLICE KIT FIBRLOK II PDF资料下载
参数资料
| 型号： | 2559 |
| 厂商： | 3M |
| 文件页数： | 4/4页 |
| 文件大小： | 0K |
| 描述： | SPLICE KIT FIBRLOK II |
| 标准包装： | 1 |
| 系列： | Fibrlok™ |
| 类型： | 接线头 |
| 其它名称： | 0-00-51115-29999-5 00051115258008 00051115299995 5111529999 51115299995 80-6113-2375-1 80611323751 |
7.8 Grasp the left fiber about 2 inches from the holder and push the
fiber in until it bows about 1/8 to 1/4 inch (3mm to 6mm). Push
down on the actuation lever until the Fibrlok II Splice is actuated.
An audible click can be heard and you should feel the splice cap
snap down into place when completely closed. The cap should be
level with the Fibrlok splice top surface.
7.9 Release the bow in the fiber and fully close the left buffer clamp.
Again, you will hear an audible snap.
8.0 Fiber Repositioning
8.1 If high loss is observed after the splice has been actuated, it is possible that the fiber ends are separated.
In this case, lift the splice cap and reposition the fiber ends, as instructed below.
8.2 While the splice is still in the holder assembly, lift the actuation
lever and insert the cap removal tool over the splice cap. Grasp
both sides of the splice holder base and lift the cap up and off the
splice while gently rocking lengthwise. Replace the cap parallel
to the top, but raised about 1mm (0.04 inch) as it snaps into
place.
8.3 Carefully reposition fiber. Refer to section 7.0 for proper
fiber centering and splice actuation.
8.4 Place splice cap back on the Fibrlok splice and push down the
actuation lever until cap has been fully actuated.
8.5 If after two attempts, an acceptable splice loss is not obtained,
remove fibers and replace the Fibrlok splice with a new splice.
Redo fiber preparation (section 5) by re-stripping, cleaning, and
cleaving both fibers. Then repeat steps in section 7.
8.6 Upon completion, the actuation lever can be removed and
discarded if desired.
Rev B
相关PDF资料 |
PDF描述 |
|---|---|
| XREWHT-L1-0000-006E4 | LED NEUTRAL WHITE 7X9MM SMD |
| MCM500VKIT2 | KIT METAL CLAD 10PF-1000PF 500V |
| S-Y2 | SAFETY CAP Y2 MLCC KIT SMD |
| XREWHT-L1-0000-004F8 | LED WARM WHITE 7X9MM SMD |
| XREWHT-L1-0000-004F7 | LED WARM WHITE 7X9MM SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 2559_07 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:PROTECTED QUAD POWER DRIVER |
| 25590/25520/Q | 制造商:UNBRANDED 功能描述:BEARING ROLLER TAPER |
| 2559000 | 制造商:KROY INC 功能描述:THERMAL PRINTHEAD CLEANING KIT (25 PACK) 制造商:Kroy 功能描述:Labels 制造商:Kroy 功能描述:LABELS; Kit Contents:Thermal Printhead Cleaning Products ;RoHS Compliant: Yes |
| 2-5-5906 | 功能描述:TAPE 5906 VHB FOAM 2" X 5YD 制造商:3m (tc) 系列:* 零件状态:有效 标准包装:1 |
| 2-5-5907 | 功能描述:TAPE 5907 VHB FOAM 2" X 5YD 制造商:3m (tc) 系列:* 零件状态:有效 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。