- 您现在的位置：买卖IC网 > PDF目录41410 > 2DA31SBRP (ITT CANNON) 31 CONTACT(S), MALE, D SUBMINIATURE CONNECTOR, SOLDER PDF资料下载
参数资料
| 型号： | 2DA31SBRP |
| 厂商： | ITT CANNON |
| 元件分类： | D-微型连接器 |
| 英文描述： | 31 CONTACT(S), MALE, D SUBMINIATURE CONNECTOR, SOLDER |
| 封装： | ROHS COMPLIANT |
| 文件页数： | 2/10页 |
| 文件大小： | 607K |
| 代理商： | 2DA31SBRP |
69
www.ittcannon.com
Dimensions shown in inch (mm)
Specifications and dimensions subject to change
The Centi Line - .075" Contact Spacing
2D/CTA
CTA Assembly Instructions
.275 (6.98)
MAX.
.475 (12.06)
MAX.
INSERTION
Guide Posts
Polarizing Posts
1. Place the connector into the slot in the assembly block
with the arrows on the insulator pointing downward. The
connector will bottom against the internal shoulder in the
groove in the assembly block. Start contact insertion by
placing the crimped contact in the cavity by hard.
3. With firm steady pressure, push the contact into the
cavity until the resilient internal shoulder snaps into the
locking groove in the contact. To prevent over insertion,
the tool tip bottoms against the rear of the insulator.
4. The guide post and polarizing posts are inserted in teh
same manner as the contacts. The guide posts are inserted
into the socket insulator, and the polarizing posts are
inserted into the pin insulartor. The corresponding contact
in the mating insulator must be removed for each.
2. Position the insertion tool tip on the rear of contact as
shown. The insulation must be pulled back from the crimp
pot approximately 1/32" to allow the tool tip to butt
against the contact crimp pot.
EXTRACTION
1. To extract the contacts, place the conector face up in
the assembly block so that the contact to be extracted is
in the end of the block that has a fully slotted opening.
2. The pin extraction tool tip is tubular, slides over the pin
bundle and butts against the front shoulder of the pin. The
socket extraction tool is a solid rod that fits into the socket
contact, the external shoulder butts against the contact
socket shoulder.
3. Insert the extraction tool into the cavity and apply firm
pressure until the contact is pushed thru the rear of the
connector.
4. Lift the insulator from the groove and pull the contact
out. Repeat for balance of contacts to be removed.
相关PDF资料 |
PDF描述 |
|---|---|
| 2DA31S | 31 CONTACT(S), FEMALE, D SUBMINIATURE CONNECTOR, CRIMP |
| 2DB52P | 52 CONTACT(S), MALE, D SUBMINIATURE CONNECTOR, CRIMP |
| 2DB52SBRP | 52 CONTACT(S), MALE, D SUBMINIATURE CONNECTOR, SOLDER |
| 2DB52S | 52 CONTACT(S), FEMALE, D SUBMINIATURE CONNECTOR, CRIMP |
| 2DC79P | 79 CONTACT(S), MALE, D SUBMINIATURE CONNECTOR, CRIMP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 2DA31SBRP-A156 | 制造商:ITT Interconnect Solutions 功能描述:2DA31SBRP-A156 / 096260-0114 / Micro |
| 2DA-31SF0 | 制造商:ITT Interconnect Solutions 功能描述:MICRO DD 31POS SKT |
| 2DA31S-F0 | 功能描述:MICRO DD 31POS SKT RoHS:否 类别:连接器，互连式 >> D-Sub，D 形 - 外壳 系列:2D 标准包装:40 系列:180 连接器类型:母触点插座 位置数:78 连接器类型:D-Sub，高密度 触点类型：:信号 行数:4 外壳尺寸，连接器布局:5（DD，D）高密度 法兰特点:配接侧（4-40） 安装类型:自由悬挂 外壳材料，表面处理:钢，带黄色铬酸盐镀层 外壳表面处理厚度:- 特点:- 请注意:不提供触点 包装:散装 防护等级:- 插拔次数:- 电介质材料:聚对苯二甲酸丁二酯（PBT），玻璃纤维增强型 颜色:黑 工作温度:-50°C ~ 100°C 其它名称:3878FEA |
| 2DA31SF0-MIT | 制造商:ITT Interconnect Solutions 功能描述:2DA-31SF0 WITH DSUB SHELLS |
| 2DA31S-F161 | 制造商:ITT Interconnect Solutions 功能描述:2DA31S-F161 - Bulk |
发布紧急采购，3分钟左右您将得到回复。