- 您现在的位置：买卖IC网 > PDF目录41410 > 2DB52SBRP (ITT CANNON) 52 CONTACT(S), MALE, D SUBMINIATURE CONNECTOR, SOLDER PDF资料下载
参数资料
| 型号： | 2DB52SBRP |
| 厂商： | ITT CANNON |
| 元件分类： | D-微型连接器 |
| 英文描述： | 52 CONTACT(S), MALE, D SUBMINIATURE CONNECTOR, SOLDER |
| 封装： | ROHS COMPLIANT |
| 文件页数： | 10/10页 |
| 文件大小： | 607K |
| 代理商： | 2DB52SBRP |
The Centi Line - .075" Contact Spacing
2D/CTA
2D/CTA CENTI-LOCTM Connectors Assembly Instructions
68
www.ittcannon.com
The Double Density D/CTA CENTI-LOC Connectors
are highly reliable and simple connectors to use.
There are a few helpful suggestions that will assure
complete satisfaction when followed:
1. The following instructions should be followed.
2. The proper crimp tool and locator (if required)
must be used. These tools have been designed
for use with this product. Substitutions of crimp-
ing equipment may result in connector failure at
the assembly operation.
3. After crimping a contact to a lead it is of vital
importance that the proper tool be used to assure
seating the contact in the insulator in the proper
position. Any substitution of insertion tools may
result in over or under insertion of the contact
which may damage the retention system of the
insulator.
4. The female (socket) side of the connector has
been designed with a controlled float to allow for
ease of mating. To avoid reducing this float or
causing a splaying of the contacts, any unneces-
sary strain caused by clamping the leads too
close to the rear of the connector should be
avoided.
Use of recommended tooling together with proper
assembly techniques will pay dividends in reliability
and reduced costs.
2D Assembly Instructions
Cut the wires to length required and strip .100" of
insulation from the end to be crimped. Check for
cut or broken wires and frayed insulation.
Using the proper crimp tool and locator, insert the
contact into the locator. Insert the stripped end of the
wire into the contact crimp pot, and crimp the contact to
the wire. Squeeze the handles firmly to insure a proper
crimp (tool will not release if crimping is incomplete).
NOTE: Contact stop must be changed in tool locator
when crimping pin and socket contacts.
1.
Place
the
proper
insertion
tip
in
the
insertion/-extraction handle and put the tip over the
wire as shown. The tool tip will butt up against the
crimp pot. Connector must be firmly supported
during both insertion and extraction operations.
2. Using a firm, steady pressure, push the contact into
the cavity until the resilient internal shoulder in the
insulator snaps into the locking groove in the contact.
The shoulder of the tool tip bottoms against the rear
of the insulator, preventing over-insertion. Repeat for
balance of contacts.
1. For contact extraction, remove the insertion tool
tip and replace it with the proper extraction tool tip.
(The socket tip will fit into the socket, and the pin
tip will slide over the pin bundle). Insert the tool tip
into the contact cavity: (the pin tip will butt up
against the shoulder of the pin contact, and the
socket tip will bottom out in the socket contact.)
2. Apply a firm, steady pressure until the contact is
released from the internal shoulder in the insulator. The
shoulder of the tool tip bottom against the insulator
face to prevent damage to the internal shoulder.
Remove the tool tip and pull the contact from the rear
of the connector. Repeat for the balance of contacts to
be removed.
WIRE STRIPPING
.100
(2.54)
CONTACT INSERTION
CONTACT EXTRACTION
CONTACT CRIMPING
Dimensions shown in inch (mm)
Specifications and dimensions subject to change
相关PDF资料 |
PDF描述 |
|---|---|
| 2DB52S | 52 CONTACT(S), FEMALE, D SUBMINIATURE CONNECTOR, CRIMP |
| 2DC79P | 79 CONTACT(S), MALE, D SUBMINIATURE CONNECTOR, CRIMP |
| 2DC79SBRP | 79 CONTACT(S), MALE, D SUBMINIATURE CONNECTOR, SOLDER |
| 2DC79S | 79 CONTACT(S), FEMALE, D SUBMINIATURE CONNECTOR, CRIMP |
| 2DD100P | 100 CONTACT(S), MALE, D SUBMINIATURE CONNECTOR, CRIMP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 2DB52SBRP-2 | 制造商:ITT 功能描述:MICRO 制造商:ITT Interconnect Solutions 功能描述:MICRO |
| 2DB-52SF0 | 制造商:ITT Interconnect Solutions 功能描述:MICRO DB 52POS SKT 制造商:ITT Interconnect Solutions 功能描述:CAN2DB-52SF0 |
| 2DB52S-F0 | 功能描述:MICRO DB 52POS SKT RoHS:否 类别:连接器，互连式 >> D-Sub，D 形 - 外壳 系列:2D 标准包装:40 系列:180 连接器类型:母触点插座 位置数:78 连接器类型:D-Sub，高密度 触点类型：:信号 行数:4 外壳尺寸，连接器布局:5（DD，D）高密度 法兰特点:配接侧（4-40） 安装类型:自由悬挂 外壳材料，表面处理:钢，带黄色铬酸盐镀层 外壳表面处理厚度:- 特点:- 请注意:不提供触点 包装:散装 防护等级:- 插拔次数:- 电介质材料:聚对苯二甲酸丁二酯（PBT），玻璃纤维增强型 颜色:黑 工作温度:-50°C ~ 100°C 其它名称:3878FEA |
| 2DB52S-F115 | 制造商:ITT Interconnect Solutions 功能描述:2DB52S-F115 - Bulk |
| 2DB52S-F115-FO | 制造商:ITT Interconnect Solutions 功能描述:2DB52S-F115-FO - Bulk |
发布紧急采购，3分钟左右您将得到回复。